2 BASIC OPERATION
12
Confidential
FUNC (K)/Ver. 1.01
2.9 Receive
2.9.1 Conventional Group
The transceiver can communicate with the receiving party
only if the received QT/DQT code matches the configured
QT/DQT code. The transceiver emits the received audio
when the QT/DQT code matches.
Receive frequency and QT/DQT Decode must be
configured by using KPG-101D.
Transceiver Operation
1.
Select a Zone-channel to be used.
Changing the Zone on page 9, 2.5 Changing the
CH/GID on page 9.)
2.
Adjust the volume level if needed when the
transceiver receives a call.
Configuration using KPG-101D
•
Configuring the Receive Frequency (Refer to
FPRG 6.4.3 Receive Frequency.)
•
Configuring the QT/DQT Decode (Refer to FPRG
6.4.5 QT/DQT Decode.)
2.9.2 Trunking System (TK-3173 only)
The transceiver can communicate with the receiving party
only if the received LTR ID matches the configured LTR
ID. The transceiver emits the received audio when the
LTR ID matches.
Receive Frequency and the Decode ID must be
configured by using KPG-101D.
Transceiver Operation
1.
Select a Zone-Group ID to be used.
Changing the Zone on page 9, 2.5 Changing the
CH/GID on page 9.)
2.
Adjust the volume level if needed when the
transceiver receives a call.
Configuration using KPG-101D
•
Configuring the Receive Frequency (Refer to
FPRG 6.5.3 Receive Frequency.)
•
Configuring the Decode ID (Refer to FPRG 6.6.4
Decode ID.)
2.10 Transmit
2.10.1 Conventional Group
The transceiver sends the programmed QT/DQT code if
the
PTT
switch is pressed. If the sent QT/DQT code
matches the QT/DQT code configured at the receiving
party’s transceiver, the caller can communicate with the
receiving party.
The transceiver transmits Reverse Burst if QT is used, or
sends the Turn-off code if DQT is used to close the
speaker of the receiving party’s transceiver when the
PTT
switch is released.
Transmit frequency and QT/DQT Encode must be
configured by using KPG-101D.
Transceiver Operation
1.
Select a Zone-channel to be used.
Changing the Zone on page 9, 2.5 Changing the
CH/GID on page 9.)
2.
Confirm that the channel is available.
3.
Speak into the microphone while pressing the
PTT
switch.
4.
Release the
PTT
switch to stop the transmission.
Configuration using KPG-101D
•
Configuring the Transmit Frequency (Refer to
FPRG 6.4.4 Transmit Frequency.)
•
Configuring the QT/DQT Encode (Refer to FPRG
6.4.6 QT/DQT Encode.)
2.10.2 Trunking System (TK-3173 only)
The transceiver sends the LTR ID while the
PTT
switch is
pressed to transmit. The transceiver connects to the
repeater and waits to receive data that is echoed back.
If the data is correct, the transceiver assumes the
connection is properly established and re-transmits to the
receiving party.
When the transmitted LTR ID matches the LTR ID
configured in the receiving party’s transceiver, the
transceiver can communicate with the receiving party.
When the
PTT
switch is released, the transceiver sends
EOT data to close the speaker of the receiving party’s
transceiver.
Transmit Frequency and Encode ID must be configured
by using KPG-101D.
