Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 57 / 142

background image

15 LTR TRUNKING

FUNC (K)/Ver. 1.01

Confidential

45

15.1.2 Scan Weight

Scan Weight can be used to configure the duration to
decode the LTR ID sent from the repeater during the
scan.
The transceiver uses the LTR ID provided by the repeater
to unmute and Trunkout. If there are several Group IDs
having the same Home number in the LTR Trunked
Radio System, other users having the same Home
number must Trunkout. Therefore, it may take a long
time for a user to receive their own LTR ID.
In this case, Scan Weight must be configured longer so
as not to miss LTR Data during the scan.
1 weight is approximately 500 ms long.
Scan Weight can be configured by using KPG-101D.

Configuration using KPG-101D

• Configuring the Scan Weight (Refer to FPRG

6.3.2 Scan Weight.)

15.1.3 Wide/ Narrow

Select the desired Channel Spacing for the available LTR
Trunked Radio System.
Wide/ Narrow can be configured by using KPG-101D.

Configuration using KPG-101D

• Configuring the Wide/ Narrow (Refer to FPRG

6.3.3 Wide/ Narrow.)

15.1.4 Data Zone-GID

Data Zone-GID can be used to separate the GIDs for
data communications from the GIDs for voice
communications.

(Refer to 23.1.2 Data Zone-CH/GID on

Data Zone-GID can be configured by using KPG-101D.

Configuration using KPG-101D

• Configuring the Data Zone-GID (Refer to FPRG

6.3.4 Data Zone-GID.)

15.1.5 Data Delay Time

The Data Delay Time is the duration from when the
transceiver starts transmitting to when the transceiver
starts sending LTR Data. This delay time can be used
when the transceiver cannot establish a link to the
repeater.
The Data Delay Time can be configured by using KPG-
101D.

Configuration using KPG-101D

• Configuring the Data Delay Time (Refer to FPRG

6.3.5 Data Delay Time.)

15.1.6 Home GID

Home GID can be used to jump to a frequently used GID
with a press of a key.

(Refer to 2.7 Home CH/GID on

Home GID can be configured by using KPG-101D.

Configuration using KPG-101D

• Configuring the Home GID (Refer to FPRG 6.3.6

Home GID.)

• Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

15.1.7 Operator Selectable

Home-GID

Operator Selectable Home-GID can be used to configure
the Home GID. A user can change the Home GID by
selecting the GID to be configured as the Home GID and
pressing and holding the

Home CH/GID

key for 3

seconds while this function is enabled.
Operator Selectable Home-GID can be configured to be
enabled or disabled by using KPG-101D.

Configuration using KPG-101D

• Configuring the Operator Selectable Home-GID

(Refer to FPRG 6.3.7 Operator Selectable Home-
GID.)

«
...
55
56
57
58
59
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

SOLAR e POWER CASE 800

Brand: Wagan Pages: 19

Brand: Sincro Pages: 40

Brand: Audio Pro Pages: 53

Brand: Denver Pages: 80

Brand: Pixel Pages: 4

ElectroMate VEC095

Brand: Vector Pages: 20

Brand: Generac Power Systems Pages: 72

Brand: Powermate Pages: 16

Brand: OWI Pages: 1

Brand: Cobra Pages: 42

Brand: Miller Pages: 56

Brand: Bluetti Pages: 56

Brand: Sole Diesel Pages: 104

Brand: Midland Pages: 16

Brand: Midland Pages: 18

Brand: Alinco Pages: 32

Brand: Klein Tools Pages: 20

Brand: Campbell Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands