Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 103 / 142

background image

20 FLEETSYNC

FUNC (K)/Ver. 1.01

Confidential

91

20.3.8 Target Fleet/ Target ID (Status

Message)

Target Fleet/ Target ID is the target FleetSync ID for
sending the following Status Messages:
•

Status Message transmission using the

Call 1

or

Call 2

key

•

Transmission when the transceiver enters
Transmission Mode by pressing the

Status

key

Target FleetSync ID can be configured by using
KPG-101D. The FleetSync ID of the dispatcher is
normally configured for the Target Fleet/ Target ID
(Status Message).

Configuration using KPG-101D

•

Configuring the Target Fleet (Refer to FPRG
6.12.3 Parameter Tab - Target Fleet (Status
Message).)

•

Configuring the Target ID (Refer to FPRG 6.12.3
Parameter Tab - Target ID (Status Message).)

20.3.9 Status 80 - 99 (Special)

Status 80 to 99 (reserved status) are used to make the
specified operations. This function prevents a user from
accidentally sending Status 80 to 99.
Configure whether the transceiver sends Status 80 to 99
(Special).

Configuration using KPG-101D

•

Configuring the Status 80 - 99 (Special) (Refer to
FPRG 6.12.1 General 1 Tab - Status 80 - 99
(Special).)

20.3.10 Emergency Status Response

Emergency Status Response is the transceiver’s reaction
to receiving an emergency status message.
“MAN DOWN” appears on the display when the
transceiver receives Status 98. “EMG” appears on the
display when the transceiver receives Status 99.
However, the configured data appears on the display
when the Emergency Status is configured in the Status
List.
The following functions can be configured for Emergency
Status Response by using KPG-101D.

Table 20-11 Emergency Status Response Operation

Configuration using KPG-101D

•

Configuring the Emergency Status Response
(Refer to FPRG 6.12.1 General 1 Tab - Emergency
Status Response.)

Emergency Status

Response

Operation

None

The transceiver activates as normal.

Alert Tone

Alert Tone configured for Emergency
Status sounds when receiving an
Emergency Status. Press any key other
than the

Volume Up

or

Volume Down

key to stop the Alert Tone.

«
...
101
102
103
104
105
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Xpress XMCK-20KC

Brand: Audiovox Pages: 2

Brand: Generac Power Systems Pages: 116

Brand: GENMAX Pages: 28

Brand: Alba Pages: 10

Brand: Yaesu Pages: 32

Brand: Kohler Pages: 72

Brand: Sirius Satellite Radio Pages: 36

Brand: Panacom Pages: 10

Brand: Roberts Pages: 12

Brand: Ericsson Pages: 16

Brand: P.Lindberg Pages: 58

Brand: Skydio Pages: 7

Brand: Koshin Pages: 36

Brand: PACH & COMPANY Pages: 3

Brand: Xoro Pages: 146

Brand: Midland Pages: 10

Brand: Motorola Pages: 24

Brand: Motorola Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands