20 FLEETSYNC
100
Confidential
FUNC (K)/Ver. 1.01
Configuration using KPG-101D
•
Configuring the Message Display Type (Refer to
FPRG 6.12.1 General 1 Tab - Message Display
Type.)
20.7.5 PC Interface Protocol
There are 2 types of PC Interface Protocols: Version 1
and Version 2.
Version 1 is same protocol used in the TK-780 and TK-
7150.
Version 2 is the new protocol. In this version, a
Sequence number is added to the command, and ACK
(acknowledge) can be sent after receiving a command.
Therefore, it is easier to manage and control the
transceiver from the PC.
PC Interface Protocol can be configured by using KPG-
101D.
Configuration using KPG-101D
•
Configuring the PC Interface Protocol (Refer to
FPRG 6.12.1 General 1 Tab - PC Interface
Protocol.)
20.7.6 Manual Dialing
Manual Dialing can be used to directly enter the Fleet and
ID numbers.
Enter directly the Fleet and ID using the keypad or
Selector
when Manual Dialing is enabled.
Manual Dialing can be configured to be enabled or
disabled by using KPG-101D.
Configuration using KPG-101D
•
Configuring the Manual Dialing (Refer to FPRG
6.12.1 General 1 Tab - Manual Dialing.)
20.7.7 Selective Call Alert LED
Selective Call Alert LED can be used to make the
Selective Call Alert LED blink when the transceiver
receives a Selcall.
(Refer to 20.2 Selcall Function on
The Selective Call Alert LED can be configured to blink by
using KPG-101D.
Configuration using KPG-101D
•
Configuring the Selective Call Alert LED (Refer to
FPRG 6.12.1 General 1 Tab - Selective Call Alert
LED.)
20.7.8 Interfleet Call
This function allows a user to make a call to a FleetSync
ID in a different Fleet.
A user can inhibit making a call to a FleetSync ID having
a different Fleet number by disabling Interfleet Call
(Uncheck) by using KPG-101D. This function also
prevents a user from making a call to an Interfleet ID
inadvertently.
Interfleet Call can be configured to be enabled or disabled
by using KPG-101D.
Note:
A user can make an Interfleet Call regardless of the
Interfleet configuration when making an Interfleet Call with a
PC Command.
Configuration using KPG-101D
•
Configuring the Interfleet Call (Refer to FPRG
6.12.1 General 1 Tab - Interfleet Call.)
20.7.9 Group ID
A user can make a Group Call using FleetSync. The
same Group ID must be assigned to transceivers in each
group when making a Group Call. A user can make a call
to a smaller unit than Fleet Call and Supervisor Call.
Normally, Group ID is used in the same Fleet.
Table 20-17 Response Scenarios for Group IDs
Group ID can be configured if the
Group ID
checkbox is
checked. A user can configure a maximum of 10 groups.
Group ID can be configured to be enabled or disabled by
using KPG-101D.
Configuration using KPG-101D
•
Configuring the Group ID (Refer to FPRG 6.12.1
General 1 Tab - Group ID.)
•
Configuring the Group ID (1 to 10) (Refer to FPRG
6.12.1 General 1 Tab - Group ID (1 to 10).)
Call Type
Response
ID Configured in
ID List
ID Not Configured
in ID List
Group Call
A user can respond
with a Group Call.
A user can respond
with a Group Call.
However, a user may
not be able to
respond according to
the Interfleet
configuration and
Unit Encode Block
configuration.
