Kenwood TK-2170 SERIES Function Reference Download | Manualshive

Page: 72 / 142

background image

60

Confidential

FUNC (K)/Ver. 1.01

17 OST

OST (Operator Selectable Tone) can be used to change
the Decode and Encode pair of the QT/DQT signaling
without changing the transmit frequency and receive
frequency.
If multiple talk groups use the same frequency but a
different QT/DQT is used, the dispatcher can specify the
talk group using this function.
A maximum of 40 pairs of QT/DQT Decode and
QT/DQT Encode can be configured in the OST Table. A
QT/DQT Encode/ Decode pair and the OST Table can be
switched for each channel by pressing the

OST

key.

A QT/DQT Decode/ Encode pair for OST can be
configured for each channel by using KPG-101D.

Note:

OST is disabled if the zone or channel is changed. OST is
enabled again if the transceiver returns to a channel while OST
Status Memory is enabled.

(Refer to 17.1 OST Status Memory

If Operator Selectable Tone (OST) and Talk Around are both
activated; the transceiver executes OST first.

Transceiver Operation

z

Enabling OST
1.

Press the

OST

key while OST is disabled.

The OST Name appears for 2 seconds and the
OST function is enabled.

z

Disabling OST
1.

Press the

OST

key while OST is enabled.

OST will be disabled.

z

Selecting the OST List
1.

Press and hold the

OST

key for 1 second.

The transceiver enters List Selection Mode.

2.

Select the desired OST List.
•

Using the

PF

keys

Press the

[<B]

or

[C>]

key.

•

Using the

Selector

*1

Turn the

Selector

.

3.

Press the

[S]

or

[*]

key.

The selected OST List is enabled.

*1

If the List Selection Key (Selector) is enabled.

Configuration using KPG-101D

•

Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

17.1 OST Status Memory

OST Status Memory can be used to stack the OST codes
configured for each channel even if the transceiver is
turned OFF or the channel is changed.
OST will be disabled when the channel is changed or the
transceiver is turned OFF while this function is disabled.
OST Status Memory can be configured to be enabled or
disabled by using KPG-101D.

Configuration using KPG-101D

•

Configuring the OST Status Memory (Refer to
FPRG 6.7.3 Conventional Tab - OST Status
Memory.)

17.2 Tone Off

Tone Off enables a user to select “Tone Off” in OST List
selection mode.
QT/DQT Encode/ Decode is disabled if “Tone Off” is
selected.
Tone Off can be configured to be enabled or disabled by
using KPG-101D.

Configuration using KPG-101D

•

Configuring the Tone Off (Refer to FPRG 6.7.3
Conventional Tab - Tone Off.)

«
...
70
71
72
73
74
...
»

Summary of Contents for TK-2170 SERIES















































































































































Reviews:

No comments

Related manuals for TK-2170 SERIES

Brand: Eton Pages: 18

A1101R09 Series

Brand: Anaren Pages: 26

Brand: Ham International Pages: 25

Brand: Rassbach Communications Pages: 5

Brand: Yaesu Pages: 2

Brand: Albrecht Pages: 23

Brand: Ericsson GE Pages: 16

Brand: G-Power America Pages: 53

Brand: Rampage Pages: 32

Brand: Generac Power Systems Pages: 2

Brand: OWI Pages: 1

Brand: ZUM Radio Pages: 40

Brand: Briggs & Stratton Pages: 56

Brand: Kompernass Pages: 20

Brand: Miller Pages: 56

Brand: Dared Pages: 6

Brand: Audizio Pages: 36

Brand: ETQ Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands