Kenwood TK-2170 SERIES Function Reference Download

Page: 134 / 142

122

Index

Contents

Confidential

FUNC (K)/Ver. 1.01

25 VOX

VOX function can be used to transmit automatically by
speaking into the microphone without using the

PTT

switch.
This function is useful when a headset microphone is
installed on the transceiver but the

PTT

switch cannot be

pressed.
This function is available only when a user wears the
headset and the transceiver is in Conventional Group.
If the

VOX Function

checkbox is checked, VOX is

activated when the transceiver is turned ON.

Note:

The transceiver cannot transmit with VOX if the transmission is
restricted by Stun, etc.

If the transceiver terminates the VOX transmission due to the
Time-out Timer, the transceiver does not transmit until both the
VOX and

PTT

switch are disabled.

Transceiver Operation

Enabling VOX
1.

Press and hold the

VOX

key for more than 2

seconds.
The “

” icon (left) appears and VOX is

enabled.

Disabling VOX
1.

Press and hold the

VOX

key for more than 2

seconds.
The “

” icon (left) disappears and VOX is

disabled.

Note:

The VOX configuration is stored even if the transceiver is
turned OFF.

Configuration using KPG-101D

•

Assigning functions to the

keys (Refer to

FPRG 6.8 Key Assignment.)

25.1 Configuring the VOX

Function

The following functions relevant to the VOX function can
be configured by using KPG-101D:
•

VOX Gain Level

•

VOX Delay Time

•

Transmit Inhibit while Receiving

•

Cancel Operation

•

VOX Proceed Tone

25.1.1 VOX Gain Level

VOX Gain Level can be used to configure the sensitivity
of the microphone to transmit.
VOX Gain Level can be configured by using KPG-101D.
VOX Gain Level can also be configured using the keys on
transceiver.

Transceiver Operation

Press the

VOX

key.

The transceiver activates VOX.
The “

” icon (left) and the current VOX Gain

Level appear on the display.

Adjust the VOX Gain Level using the

[<B]

[C>]

key or

Selector

If the List Selection Key (Selector) is enabled.

Note:

The LED lights orange when the Mic input level reaches the
transmission reference value. In this case, the transceiver
does not actually transmit.

Press the

Side 1

key.

The channel name or number appears on the
display.
VOX is enabled.

Note:

The VOX Gain Level configuration is retained even if the
transceiver is turned OFF.

Summary of Contents for TK-2170 SERIES















































































































































Search results

Summary of Contents for TK-2170 SERIES

Reviews:

Related manuals for TK-2170 SERIES

Brands by name

Popular brands

Kenwood TK-2170 SERIES, Function Reference

Search results

Summary of Contents for TK-2170 SERIES

Reviews:

Related manuals for TK-2170 SERIES

Brands by name

Popular brands