![background image](http://html1.mh-extra.com/html/keithley/4200-scs/4200-scs_user-manual_3981678228.webp)
3-122
4200-900-01 Rev. K / February 2017
Section 3: Common Device Characterization Tests
Model 4200-SCS User’s Manual
9. Route triax from SMU4 to the DUT array BL1 connection. Connect cable to probe
manipulator.
10. Take an SMA Tee and connect one SMA-to-BNC adapter to one of the female connectors.
11. Connect the assembly from step 5 to one Triax-to-SMA Adapter.
12. Connect one 8 inch (20.3 cm) SMA cable to the remaining SMA female connector.
13. Connect one 5 foot (1.5 m) black BNC cable to the BNC connection.
14. Perform steps 10-13 two more times.
15. Take one of the cable assemblies from step 14, connect the SMA to CHANNEL 2 of the
PG2 in the left most slot (PG2 in the slot with the highest number).
16. Carefully insert the LEMO Triax connector from step 15 into the Force connector on the
SMU in Slot 4.
17. Route BNC cable from SMU4 to the DUT array WL2 terminal. Use a Triax-to-BNC adapter,
if necessary. Connect cable to probe manipulator.
18. Take one of the cable assemblies from step 14, connect the SMA to CHANNEL 1 of the
PG2 in the left most slot (PG2 in the slot with the highest number).
19. Carefully insert the LEMO Triax connector from step 18 into the Force connector on the
SMU in Slot 3.
20. Route BNC cable from SMU3 to the DUT array BL2 connection. Connect Triax-to-BNC
adapter, if necessary. Connect cable to probe manipulator.
21. Take one of the cable assemblies from step 14, connect the SMA to CHANNEL 2 of the
PG2 in the right-most slot (PG2 in the slot with the lowest number).
22. Carefully insert the LEMO Triax connector from step 21 into the Force connector on the
SMU in Slot 2.
23. Route BNC cable from SMU2 to the DUT array WL2 connection. Connect Triax-to-BNC
adapter, if necessary. Connect cable to probe manipulator.
24. Take one of the cable assemblies from step 14, connect the SMA to CHANNEL 1 of the
PG2 in the right-most slot (PG2 in the slot with the lowest number).
25. Carefully insert the LEMO Triax connector from step 24 into the Force connector on the
SMU in Slot 1.
26. Route BNC cable from SMU1 to the DUT array WL1 connection. Connect Triax-to-BNC
adapter, if necessary. Connect cable to probe manipulator.
Switch matrix connection to array DUT
Cabling instructions for switch connect to an array DUT are below. Refer to
for the following procedure. These instructions are compatible with the
following projects in the Projects\_Memory folder:
• Flash-Switch
• FlashDisturb-Switch
• FlashEndurance-Switch
Unlike the direct connect methods described above, the use of a switch matrix
permits the use of SMU preamp.
1. Set up the 4200-SCS, referring to the
,
Reference manual, Connections and Configuration, page 4-1
.
2. Set up the 707 or 708 Switch matrix using the
Reference manual, Using KCON to add a
switch matrix to the system, page B-15
. See
for a suggested configuration for
the row-column connection, consistent with
3. Take one of the SMA Tees and connect the two shortest (4.25 inch or 10.8 cm) SMA cables
to either end.
Summary of Contents for 4200-SCS
Page 2: ......
Page 4: ......
Page 334: ...Index 6 4200 900 01 Rev K February 2017 Model 4200 SCS User s Manual Index...