JR ProPo XG11, Operation Manual

Page: 8 / 124

6
▋ Inserting▋and▋Removing▋the▋Transmitter▋Battery
1) While pressing the embossed mark on the rear surface of the battery lid, slide the lid in arrowed direction of the
arrow, and remove.
2) Carefully insert the rechargeable battery connector into the transmitter battery connector.
3) Fit the rechargeable battery into the battery box together with filling sponge, and mount the battery cover, taking
care not to pinch the lead wires.
▋
Charging▋the▋Transmitter▋Battery
Before charging the battery, be certain to read the precautions written on the battery label.
The transmitter operates exclusively with genuine JR Li-Fe batteries. Do not use the transmitter with other
rechargeable batteries or with dry cell batteries.
During charging, the transmitter should be switched off. When the transmitter ON, charging will not take place.
Note that if using a flight simulator with the control cable plugged into the trainer jack (and the power switch OFF
on the transmitter), it is possible to plug the charge cable into the transmitter and use the AC adaptor to supply
power. Since the built-in battery will not be used, this will allow enjoyment while conserving energy.
1) Insert the AC adaptor into the AC electric power socket.
2) Insert the plug of the AC adaptor as far as it will go into the DC power jack of the transmitter.
If the LED on the back side of the transmitter does not illuminate, an error may have occurred.
In this situation, detach the AC adapter plug, and re-insert it.
If the back side LED does not light even after the cable has been removed and inserted several times, please
contact your JR agent or distributor in your country.
3) During charging, the LED located on the back-side of transmitter will light. When charging is complete, the LED
will switch off. The standard charging time is approximately 3 hours.
4) After charging has been completed, promptly detach all the connections. Absolutely do not leave the charger
connected to the transmitter.
※ Be certain to only use the genuine JR XG11 dedicated AC adapter (NEC-A912). Charging cannot be carried out
using other AC adapters. Further, do not use this AC adapter for charging products other than the XG11.
DANGER
CAUTION
Helicopter
Airplane
Glider
WARNING
Warning！Abnormal heat generation may cause explosion of the battery!
After charging is complete, quickly detach all of the connections including the AC adaptor from outlet.
Never leave the AC adaptor connected to the transmitter or plugged into the AC outlet. This is to avoid possible
fire risk after charging the battery.
Do not use the AC
adapter while the
cord is still bundled
together, since
there will be a risk
of heat generation.
Battery connector
Battery box
Battery cover
※※※※ ※※※※ ※※※※ ※※※※ ※※※※
9V 12W AC Adaptor for Recharging
(NEC-A912)
※Note: This adaptor can only be
used when plugged into the XG11
- it is not a stand alone charger.
To the AC Electric
Power Outlet
To the Recharging Power Source jack
(Exclusively for transmitters with
built-in Li-fe rechargeable batteries)
Power source jack for
recharging (DC9V)
When removing the connector, press
the lever part to release the lock
while pulling out the connector.
DANGER
CAUTION
Helicopter
Airplane
Glider
WARNING
Battery connector
Battery box
Battery cover
※※※※ ※※※※ ※※※※ ※※※※ ※※※※
9V 12W AC Adaptor for Recharging
(NEC-A912)
※Note: This adaptor can only be
used when plugged into the XG11
- it is not a stand alone charger.
To the AC Electric
Power Outlet
To the Recharging Power Source jack
(Exclusively for transmitters with
built-in Li-fe rechargeable batteries)
Power source jack for
recharging (DC9V)
Preparation