manualshive.com logo in svg

Intel IXP2400, User Manual

Share
Download
Intel IXP2400 User Manual Download Page 74

74

 Development Tools User’s Manual

  

IXP2400/IXP2800 Network Processors
Developer Workbench

Maximum burst 1

This value is the maximum number of 16 byte blocks that the Tx FIFO 
can accept when the FIFO Status channel indicates a “Starving” 
condition.

Enable Tx flow control

This check box enable Tx flow control training between the SPI4 device 
and the network processor.

Training frequency

This value indicates the maximum interval (in TS clock cycles, with the 
TS clock being one-fourth the Tx clock Frequency) between scheduling 
of flow control training sequences.

The 

Default port parameters

 section is further divided into 

Receive

 and 

Transmit

 areas. You 

may edit these characteristics, which are:

Data rate (Mbits/sec)

Specifies the rate at which data is taken from the network and inserted 
into the port’s receive (Rx) buffer and the rate at which data is taken from 
the port’s transmit (Tx) buffer and put onto the network.

Receive buffer size

 

Specifies the number of bytes in the receive buffer. The receive buffer 
holds the data received from the network until the Network Processor 
reads it from the port.

Receive threshold

 

Specifies number of bytes that must be in the port’s receive buffer in 
order for the port to signal the Network Processor that it can select the 
port and request data from it.

Transmit buffer size

Specifies the number of bytes in the transmit buffer. The transmit buffer 
holds the data transmitted by the Network Processor until it is 
transmitted onto the network.

Low water mark

See 

High water mark

, below.

High water mark

If flow control is enabled, the high water mark is used to determine if the 
device is “Hungry” or “Satisfied”. If the number of bytes in the Tx buffer 
is between the low and high water marks, then the device tells the 
network processor that it is Hungry. If the number of bytes is above the 
high water mark, then the device tells the network processor that it is 
Satisfied.

Interpacket gap (nsec)

Specifies the amount of time between packets when receiving packets 
from and transmitting packets to the network.

Number of bytes the device strips from end of packet

Specifies the number of bytes that the device must strip from the end of 
each received packet before the packet is passed to the Network 
Processor. For example, for POS IP packets, the trailing checksum bytes 
are normally stripped.

Number of bytes of zeros the device appends to packet

Specifies the number of bytes of zeroes the device appends to the packet 
before it is transmitted by the Network Processor.

Number of extra bytes

Specifies the number of bytes that are stripped from the beginning of the 
packet before it reaches the device and appended to the beginning of the 
packet after it leaves the device, for example the Ethernet preamble.

Summary of Contents for IXP2400

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands