Intel 413808 I/O Developer'S Manual Download Page 97

Page: 97 / 824

Intel

413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

Address Translation Unit (PCI-X)—Intel

413808 and 413812

2.7.3

Uncorrectable Data Errors on the PCI Interface

Two kinds of uncorrectable data errors can occur on the PCI interface: errors as an

initiator and errors as a target.
Errors encountered as an initiator:

— Outbound Read Request

— Outbound Write Request

— Inbound Read Completions

— Inbound Configuration Write Completion Messages

As an initiator, the ATU provides an error response for uncorrectable data errors on

outbound reads, and uncorrectable data errors occurring at the target for outbound

writes. However, there is no error response for uncorrectable data errors on inbound

configuration write completion messages and inbound read completions.
Errors encountered as a target:

— Inbound Read Request (Immediate Data Transfer)

— Inbound Write Request

— Outbound Read Completions

— Outbound Split (I/O or Configuration) Uncorrectable Write Data Error Messages

— Inbound Configuration Write

— Split Completion Messages

As a target, the ATU provides an error response for uncorrectable data errors on

inbound writes, outbound read completions, outbound uncorrectable split write data

error messages, inbound configuration writes, and split completion messages.

However, there is no error response for uncorrectable data errors on inbound reads.

Summary of Contents for 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 413808 I/O

Reviews:

Brands by name

Popular brands

Intel 413808 I/O, Developer'S Manual

Search results

Summary of Contents for 413808 I/O

Reviews:

Brands by name

Popular brands