Intel 413808 I/O Developer'S Manual Download Page 505

Page: 505 / 824

Intel

413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

505

System Controller (SC) and Internal Bus Bridge—Intel

413808 and 413812

7.5.6

Bridge Window Base Address Register — BWBAR

The Bridge Base Address Register (BWBAR) defines the block of memory addresses

where the Bridge Memory Window begins. The BWBAR is used in conjunction with the

BWLR to form a memory window that is used by the Bridge to claim transactions on the

South Internal Bus. The BWBAR defines the base address and describes the required

memory block size; see

Section 7.5.5, “Determining Block Sizes for Memory Windows”

on page 504

. The selected base address needs to be naturally aligned to the granularity

of the memory block size. For instance, when a 64 Kbyte memory window size is

selected, the base address needs to be 64 Kbyte address aligned (i.e., bits 15:12 of the

base address are required to be 000b).

Table 339. Bridge Window Base Address Register — BWBAR

Bit

Default

Description

31:12

FFE0 0H

Bridge Memory Window Base Address:

These bits define the actual location the Bridge responds to

for accesses to the Bridge Memory Window on the South Internal Bus.

11:00

000H

Reserved.

PCI

IOP

Attributes

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

Intel XScale

processor Local Bus Address

Offset

+1780H

South XBG

Summary of Contents for 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 413808 I/O

Reviews:

Brands by name

Popular brands

Intel 413808 I/O, Developer'S Manual

Search results

Summary of Contents for 413808 I/O

Reviews:

Brands by name

Popular brands