manualshive.com logo in svg

Intel 413808 I/O, Developer'S Manual

Share
Download
Intel 413808 I/O Developer'S Manual Download Page 567

Intel

®

 413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

567

Interrupt Controller Unit—Intel

®

 413808 and 413812

10.3

The Intel XScale

®

 Processor Exceptions Architecture

The Intel XScale

®

 processor supports five types of exceptions

16

, and a privileged 

processing mode for each type.

• IRQ and FIQ internal interrupt exceptions (normal and fast interrupts, respectively)

• memory aborts (used to implement memory protection or virtual memory)

• attempted execution of an undefined instruction

• software interrupts (SWIs) (used to make a call to an Operating System)

When an exception occurs, some of the standard registers are replaced with registers 

specific to the exception mode. All exceptions have replacement (or banked) registers 

for R14 and R13, and one interrupt mode has more registers for fast interrupt 

processing.
After an exception, R14 holds the return address for exception processing, which is 

used both to return after the exception is processed and to address the instruction that 

caused the exception.
R13 is banked across exception modes to provide each exception handler with a private 

stack pointer (SP). The fast interrupt mode also banks R8 to R12, so that interrupt 

processing can begin without the need to save or restore these registers. There is a 

seventh processing mode, System Mode, that does not have any banked registers (it 

uses the User mode registers), which is used to run normal (non-exception) tasks that 

require a privileged processor mode.

10.3.1

CPSR and SPSR

All other processor state is held in status registers. The current operating processor 

status is in the Current Program Status Register or CPSR. The CPSR holds:

• Four condition code flags (Negative, Zero, Carry and Overflow)

• Two interrupt disable bits (one for each type of interrupt)

• Five bits which encode the current processor mode

All five exception modes also have a Saved Program Status Register (SPSR) which 

holds the CPSR of the task immediately before the exception occurred. Both the CPSR 

and SPSR are accessed with special instructions.

10.3.2

The Exception Process

Note:

Refer to the System/Software Architecture Specification for details on the exception 

process for the 4138xx in TPER mode during the common boot phase.
When an exception occurs, the Intel XScale

®

 processor halts execution after the 

current instruction and begins execution at a fixed address in low memory, known as 

the exception vectors. There is a separate vector location for each exception (and two 

for memory aborts to distinguish between data and instruction accesses).
An operating system installs a handler on every exception at initialization. Privileged 

operating system tasks normally run in System mode to allow exceptions to occur 

within the operating system without state loss (exceptions overwrite their R14 when an 

exception occurs, and System mode is the only privileged mode that cannot be entered 

by an exception).

16.Exception Description from the ARM Architecture Reference Manual, p. 1-3, Copyright Advanced 

RISC Machines Ltd. (ARM) 1996

Summary of Contents for 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands