manualshive.com logo in svg

Intel 413808 I/O, Developer'S Manual

Share
Download
Intel 413808 I/O Developer'S Manual Download Page 237

Intel

®

 413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

237

Address Translation Unit (PCI Express)—Intel

®

 413808 and 413812

3.3.1

Inbound Transactions

Inbound transactions are received on the PCI Express receive port and forward to the 

4138xx internal bus. This transactions include all requests for which the ATU is the 

completer as well as completions for which the ATU was the initiator. 
Inbound request transactions which target the ATU are translated and executed on the 

4138xx internal bus. As a PCI Express completer, the ATU is capable of accepting all 

memory, I/O, and configuration request. Additionally, as a PCI Express end-point, the 

ATU would never request more memory read data than it can hold in its Inbound 

Completion Data Queue. 
Inbound memory write (and message) transactions have their headers entered into the 

inbound posted header queue (IPHQ) and data entered into the inbound posted data 

queue (IPDQ). The IPHQ/IPDQ pair are capable of holding up to 16 posted operations 

up to the size of the data queue. Inbound configuration (or I/O) write transactions use 

the inbound non posted header queue (INPHQ) and inbound non posted data queue 

(INPDQ). The INPDQ has room for one configuration or I/O write at a time. Refer to 

Section 3.8

 for details of queue operation. Inbound read transaction (memory, 

configuration, and I/O) have their header entered into the inbound non posted header 

queue (INPHQ) and the data are returned to the PCI Express requester in the outbound 

completion data queue (OCPLDQ). The INPQ is capable of holding up to 8 non posted 

requests and any associated data.
Operation of the internal bus is defined in 

Section 7.0, “System Controller (SC) and 

Internal Bus Bridge”

.PCI Express has three principal mechanisms for Transaction Layer 

Packet (TLP) routing: address, ID, and implicit. The following sections describes how 

the ATU routes and translates each type.

3.3.1.1

Inbound Address Translation

PCI Express utilizes both 32-bit and 64-bit address schemes via the 3DW and 4DW 

headers. To prevent address aliasing, all devices must decode the entire address range. 

All discussions in this section refer to 64-bit addressing. When the 3DW header is used 

the upper 32-bits of address are assumed to be 0000_0000h.
The ATU allows external PCI Express requesters to directly access the internal bus via 

address routed TLPs. These PCI Express requesters can read or write 4138xx 

memory-mapped registers or 4138xx local memory space. The process of inbound 

address translation involves two steps:

1. Address Detection.

— Verify the PCI address is within the address windows defined for the inbound 

ATU.

— When the address is outside of the ATU address registers, the transaction is 

terminated as an unsupported request (UR).

2. Address Translation.

— Translate the lower 32-bit PCI address to a 36-bit 4138xx internal bus address.

The ATU uses the following registers in inbound address window 0 translation:

•

Section 3.17.13, “Inbound ATU Base Address Register 0 - IABAR0” on page 304

• Section 3.17.28, “Inbound ATU Limit Register 0 - IALR0” on page 318

•

Section 3.17.29, “Inbound ATU Translate Value Register 0 - IATVR0” on page 319

•

Section 3.17.30, “Inbound ATU Upper Translate Value Register 0 - IAUTVR0” on 

page 319

The ATU uses the following registers in inbound address window 1 translation:

Summary of Contents for 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands