Huawei iBAT 2.0-CIM01C2 User Manual Download Page 50

Page: 50 / 79

iBAT 2.0-CIM01C2
User Manual

5 System Commissioning

Issue 07 (2019-01-02)

Parameter

Description

Battery N line

Set whether there is a battery N wire according to the actual
situation.

Single batt. group
number of HALL

Indicates the number of Hall effect sensors connected to a single
battery string.

Single batt. capacity Specifies the capacity of each battery that is connected in the battery

string in series.

Batt. installation
time

Time when the battery is installed for the first time. Does not need
to be reset when part of batteries are replaced.

iBAT number of
iBOX

Indicates the total number of iBATs managed by the iBOX.

Number of battery
strings

Indicates the total number of battery strings managed by the iBOX.

Batt. string No.

Sets the battery string numbers of the iBOXs connected in parallel
to unique ones when multiple iBOXs are connected in parallel.

Parallel
Communication
Configuration

This parameter needs to be set when multiple iBOXs are connected
in parallel and does not need to be set when there is only one iBOX.
Set

Whether the iBOX communicates directly with the NetEco

Yes

, and set

Number of iBOX configured under each UPS

Configure IP addresses for multiple iBOXs.

Modbus Config

Set ModbusTCP encryption and ModbusTCP authentication, which
are consistent with Connection Mode on the NetEco.

HALL Rerverse
Config

If the Hall effect sensor is reversely installed, you can set reverse
connection to correct it.

Basic Information

If a BCB box is configured, set

BCB configuration

Done

and

Batt. abnormal BCB trip

Enable

Time

Set the local time zone, date, and time.

IP Address

Set the IP address, subnet mask, and default gateway of the iBOX.
Set this parameter based on the IP address assigned by the
administrator.

On the iBOX WebUI homepage, choose

System Settings

Battery Curve

and set

the battery curve for each battery string.

On the

Battery Curve

page, select the battery string to be set, set

Battery Brand

and

Format

, click

Filter

Submit

Summary of Contents for iBAT 2.0-CIM01C2
















































































Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands

Huawei iBAT 2.0-CIM01C2, User Manual

Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands