Huawei iBAT 2.0-CIM01C2 User Manual Download Page 49

Page: 49 / 79

iBAT 2.0-CIM01C2
User Manual

5 System Commissioning

Issue 07 (2019-01-02)

Parameter

Description

Batt. string No.

The serial number of each battery string. Under the same CIM, the
battery string numbers must be unique.



V291B028

On the iBOX WebUI home page, choose

System Settings

Running Parameter

and set

Parallel Configuration

On the iBOX WebUI home page, choose

System Settings

Batt. String Config

and set

Batt. String Config

Parameter

Description

Parallel
Configuration

This parameter needs to be set when multiple iBOXs are connected
in parallel and does not need to be set when there is only one iBOX.
Set

Parallel Configuration

Parallel

, and set

iBOX parallel qty.

Configure IP addresses for multiple CIMs.

Current acquisition
source

The actual specifications of the Hall effect sensor prevail.

Battery N line

Set whether there is a battery N wire according to the actual
situation.

Multi-Hall cur.
setting

The number of positive or negative Hall effect sensors in a single
battery string and should be greater than or equal to 1.

Total battery
capacity



One iBOX: Capacity of one battery string x Number of battery
strings connected in parallel.



N iBOXs connected in parallel: Capacity of one battery string x
(Number of battery strings managed by iBOX 1 + … + Number
of battery strings managed by iBOX N).

Batt. installation
time

Time when the battery is installed for the first time. Does not need to
be reset when part of batteries are replaced.

iBAT Number of
iBOX

Indicates the total number of iBATs managed by the iBOX.

Number of battery
strings

The number of battery strings managed by the iBOX.

Batt. string No.

The serial number of each battery string. Under the same iBOX, the
battery string numbers must be unique.



V296B019

On the iBOX WebUI, choose

System Settings

, and set

Batt. String Config

Running Parameter

Time

and

IP Address

Parameter

Description

Current acquisition
source

The actual specifications of the Hall effect sensor prevail.

Summary of Contents for iBAT 2.0-CIM01C2
















































































Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands

Huawei iBAT 2.0-CIM01C2, User Manual

Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands