Huawei iBAT 2.0-CIM01C2 User Manual Download Page 70 | Manualshive

Page: 70 / 79

background image

iBAT 2.0-CIM01C2
User Manual

9 Maintenance

Issue 07 (2019-01-02)

Copyright © Huawei Technologies Co., Ltd.

64

Alarm Name

Alarm Severity

Possible Cause

Solution

Dis. Volt. Incon.

Minor

The battery discharge
voltage is below the lower
threshold.

1.

Check that new and old
batteries do not coexist in
the same battery string.
Mark abnormal batteries.

2.

Compare the internal
resistance of the
abnormal battery and that
of the normal battery.
Mark abnormal batteries.

3.

Compare the discharge
voltage of the abnormal
battery and that of the
normal battery. Mark
abnormal batteries.

4.

Fully charge the battery
string and prepare the
UPS backup power
supply. Then perform a
capacity test to query the
SOH of the battery. If the
SOH is abnormal, replace
the abnormal battery.

Abnormal Intern.
Resistance

Minor



A battery terminal bolt
is not tightened.



A battery terminal is
not properly connected
to a connector.



The internal resistance
of a battery is
abnormal.

1.

Check that battery
terminal screws are
tightened.

2.

Check that battery
terminals are properly
connected to connectors.

3.

Compare the internal
resistance of the
abnormal battery and that
of the normal battery.
Mark abnormal batteries.

4.

Fully charge the battery
string and prepare the
UPS backup power
supply. Then perform a
capacity test to query the
SOH of the battery. If the
SOH is abnormal, replace
the abnormal battery.

«
...
68
69
70
71
72
...
»

Summary of Contents for iBAT 2.0-CIM01C2
















































































Reviews:

No comments

Related manuals for iBAT 2.0-CIM01C2

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

Brand: Keithley Pages: 48

Brand: Bacharach Pages: 60

Brand: Bacharach Pages: 4

Brand: Bacharach Pages: 17

Brand: Oakton Pages: 69

Brand: janitza Pages: 12

Brand: Oakton Pages: 16

Brand: R&S Pages: 733

Brand: R&S Pages: 369

Brand: Lake Shore Cryotronics Pages: 97

Brand: Hanna Instruments Pages: 2

MTEK6000 Series

Brand: Metretek Pages: 81

Brand: Palstar Pages: 37

Brand: LD Didactic Pages: 2

Brand: Flowmetrics Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands