Huawei iBAT 2.0-CIM01C2 User Manual Download Page 48

Page: 48 / 79

iBAT 2.0-CIM01C2
User Manual

5 System Commissioning

Issue 07 (2019-01-02)

Figure 5-3

Step 5

Set CIM parameters.



V289B003 and earlier versions

On the CIM WebUI home page, choose

Monitoring

CIM System

Running

Parameter

, and set

Parallel Configuration

and

Basic Information

On the CIM WebUI home page, choose

System Settings

Batt. String Config

and set

Batt. String Config

Parameter

Description

Parallel
Configuration

This parameter needs to be set when multiple CIMs are connected in
parallel and does not need to be set when there is only one CIM. Set

Parallel Configuration

Parallel

, and set

CIM parallel qty.

Configure IP addresses for multiple CIMs.

Current source or
Current acquisition
source

The actual specifications of the Hall effect sensor prevail.

Battery N line

Set whether there is a battery N wire according to the actual
situation.

Multi-Hall cur.
setting

The number of positive or negative Hall effect sensors in a single
battery string and should be greater than or equal to 1.

Total battery
capacity



One iBOX: Capacity of one battery string x Number of battery
strings connected in parallel.



N iBOXs connected in parallel: Capacity of one battery string x
(Number of battery strings managed by iBOX 1 + … + Number
of battery strings managed by iBOX N).

Batt. installation
time

Time when the battery is installed for the first time. Does not need
to be reset when part of batteries are replaced.

BIM Number of
CIM

Indicates the total number of BIMs managed by the CIM.

Batt. String Qty. or
Number of battery
strings

The number of battery strings managed by the CIM.

Summary of Contents for iBAT 2.0-CIM01C2
















































































Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands

Huawei iBAT 2.0-CIM01C2, User Manual

Search results

Summary of Contents for iBAT 2.0-CIM01C2

Reviews:

Related manuals for iBAT 2.0-CIM01C2

Brands by name

Popular brands