Honeywell CM4 Technical Handbook Download Page 5

Page: 5 / 202

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

Table of Contents

Cabling Type ................................................................................................... iii
Connectors ...................................................................................................... iii

1 CM4 Overview

1.1 Introduction ................................................................................................. 1-2
1.2 Sampling and Monitoring System ....................................................... 1-3

1.2.1 Flow Connections ........................................................................... 1-3
1.2.2 Pump ................................................................................................... 1-3
1.2.3 Filters ................................................................................................... 1-3

1.3 Detection System ....................................................................................... 1-4

1.3.1 Chemcassette

Carrier .................................................................. 1-4

1.3.2 Optics and Electronics .................................................................. 1-4
1.3.3 Chemcassette

Detection System ............................................. 1-5

1.3.4 Measuring Gases ............................................................................. 1-5

1.4 Displays and Controls ............................................................................... 1-6

1.5 Electrical Connections .............................................................................. 1-6

1.5.1 I/O Panel ............................................................................................. 1-6
1.5.2 Power Connection .......................................................................... 1-7
1.5.3 Optional Serial Output .................................................................. 1-7

1.6 Alarms ............................................................................................................. 1-7

1.6.1 General and Point Gas Alarms .................................................... 1-7
1.6.2 Activating an Alarm ........................................................................ 1-7

1.7 Instrument Diagnostics ............................................................................ 1-8

2 Controls and Indicators

2.1 Introduction ................................................................................................. 2-2
2.2 Control Panel ................................................................................................ 2-2

2.2.1 Display ................................................................................................. 2-2
2.2.2 LEDs and Point ID Labels .............................................................. 2-3
2.2.3 Keypad ................................................................................................ 2-3
2.2.4 Power Indicator LED ....................................................................... 2-3

2.3 Relays .............................................................................................................. 2-4
2.4 Sample Flow Controls ............................................................................... 2-4

3 Installation

3.1 Introduction ................................................................................................. 3-2

3.1.1 Mounting Alternatives .................................................................. 3-2
3.1.2 Accessory Kit ..................................................................................... 3-2
3.1.3 Installation Steps ............................................................................. 3-2

3.2 Components and Connections for Installation ....................................... 3-3
3.3 Surveying the Installation Site ............................................................... 3-3

3.3.1 Placement of the CM4 .................................................................. 3-3
3.3.2 Exposure to Dust and Humidity................................................. 3-3
3.3.3 Sample Transport Time ................................................................. 3-4
3.3.4 Instrument Dimensions ................................................................ 3-4

TOC

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands

Honeywell CM4, Technical Handbook

Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands