Honeywell CM4 Technical Handbook Download Page 65

Page: 65 / 202

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

6-10

6.9 Function 2.8 – Print Menu

Purpose

Use the Print Menu function to print a list of CM4:

• Menu options
• Functions available from each menu

Instructions

1. Press PROGRAM to exit Monitor Mode.
2. From the 2–REVIEW MENU, choose the subfunction 8–PRINT

MENU.

2 – REVIEW MODE

8 – PRINT MENU

The CM4 prints a complete listing of the master menu. See

Section

4.6

for an example.

If the printer is not enabled or a printer fault occurs, the CM4 displays

the following:

PRINTER DISABLED

Correct the fault and repeat Steps 1 and 2.

See

Section 7.4.2

to enable the printer.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands

Honeywell CM4, Technical Handbook

Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands