manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

G-4

G.3 LonWorks Retrofit

LonWorks capability can be added to existing Model CM4 gas monitors 

using  the  items  contained  in  this  kit  and  following  the  installation 

instructions. The  LonWorks  upgrade  kit  (P/N  1874-0344)  contains  all 

the  parts  needed  to  upgrade  tabletop,  wall  mount,  and  rack  mount 

units. 
Since the kit is designed to accommodate all configurations, some of 

the parts in the kit will not be used in your installation.
The chart below shows the mounting configurations covered by this kit:

Model Table-top 

and Wall Mount 

Old Style Rack 

Mount

New Style Rack 

Mount

CM4 (S/N < 5000)

X

X

X

CM4 (S/N > 5000)

X

X

X

CM4-P

X

X

X

G.3.1 Parts

The  parts  have  been  packaged  in  seven  bags.  Check  to  make  sure 

the bags are identified and the parts are included in each bag. Do not 

remove parts from the bags until you are ready to install them.
Bag 1: LonWorks PC Board

Qty Description

Application

1 LonWorks interface with screws and foam 

insulator

All configurations

1 Label, LonWorks Option

Used  over  mounting  holes,  all 

configurations

1 Insulator (white)

Table and wall units; used between I/O and 

LonWorks interfaces

Bag 2: EPROMs

Qty Description

Application

1 EPROM LSB

Latest software revision

1 EPROM MSB

Latest software revision

Software V2.07  or  later  must  be  used  for  operating  LonWorks  on 

Model
CM4. Check the software version in your Model CM4 and replace the 

EPROMS if necessary.
Bag 3: Electrical Connection Bracket
This bag contains a bracket to mount the LonWorks interface on either 

table or wall mount units. The existing bracket in the Model CM4 does 

not  have  the  necessary  holes,  and  therefore  must  be  replaced  for 

LonWorks installations.

Qty Description

Application

1 Bracket

Desktop and wall mount

Bag 4: Electrical Cable for Serial Communication
Some of the first production Model CM4 units were shipped without 

the serial communications cable. Most of these units were installed in 

a rack mount configuration. This bag contains a cable that has been 

prefolded for rack mount installations. If the Model CM4 is a table or 

wall unit, the folds can be flattened.

Qty Description

Application

1 Serial Cable Assembly

Prefolded for rack installation

1 Spacer, Dielectric Cable

Used to secure cable to chassis wall

Bag 5: Insulator for Rack Mount
In  newer  rack-mounted  Model  CM4s,  a  metal  cover  is  installed  over 

serial  communication  interfaces.  Older  rack  mount  units  used  a 

plastic  insulator. The  plastic  insulator  is  not  large  enough  to  protect 

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Kamstrup MULTICAL 62 Technical Description preview
MULTICAL 62
Brand: Kamstrup Pages: 100
Kamstrup MULTICAL 41 Installation And User Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 41 Installation Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 12
Kamstrup flowIQ 3100 Technical Description preview
flowIQ 3100
Brand: Kamstrup Pages: 60
Kamstrup MULTICAL 403 Technical Description preview
MULTICAL 403
Brand: Kamstrup Pages: 136
Kamstrup ULTRAFLOW 54 Installation Manual preview
ULTRAFLOW 54
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 603 Technical Description preview
MULTICAL 603
Brand: Kamstrup Pages: 155
LaMotte SMART3 Quick Start Manual preview
SMART3
Brand: LaMotte Pages: 2
Lampa 38862 Manual preview
38862
Brand: Lampa Pages: 12
MADDALENA ElecTo Bulk Installation Instructions preview
ElecTo Bulk
Brand: MADDALENA Pages: 4
Macnaught M1 SERIES Instruction Manual preview
M1 SERIES
Brand: Macnaught Pages: 4
Keithley 2651A Quick Start Manual preview
2651A
Brand: Keithley Pages: 18
Cecomp F20B Instruction Manual preview
F20B
Brand: Cecomp Pages: 4
Balluff BML-S1G0-Q71 Series Condensed Manual preview
BML-S1G0-Q71 Series
Brand: Balluff Pages: 20
H-Star SS-90X Owner'S Manual preview
SS-90X
Brand: H-Star Pages: 36
BGS technic BGS 8639 Instruction Manual preview
BGS 8639
Brand: BGS technic Pages: 16
Trotec OZ-ONE Manual preview
OZ-ONE
Brand: Trotec Pages: 8
E+E Elektronik HUMIPORT 10 Manual preview
HUMIPORT 10
Brand: E+E Elektronik Pages: 48

Brands by name

Popular brands

Load more brands