manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

2-2

2.1 Introduction

This section identifies:

•  The control panel display, keypad, and LEDs (Section 2.2)
•  Relays (

Section 2.3

)

•  Sample flow controls (

Section 2.4

)

NOTE:

On newer style CM4 (S/N XXX-5000 and greater) and all CM4-P 

models, the flow controls (item 6) are located on the lower 

left of the front panel. An air filter (item 10) is located on the 

lower right.

1

2

3

4

1

4

7

2

5

8

0

3

6

9

MON

ITOR

STATU

S ALA

RM

!

LOCA

TIO

N

PROG

RAM

RESE

T

ENTE

R

3

2

1

4

10

7

8

5

1

2

3

4

1

4

7

2

5

8

0

3

6

9

MO

NIT

OR

STA

TUS

 ALA

RM

!

LOC

ATIO

N

PRO

GRA

M

RES

ET

ENT

ER

Table Mount

Wall Mount

9

6

Figure 2-1: CM4 Components and Controls

Legend

1

Tape load lever

6

Flow controls

2

20-character display

7

Keypad

3

Alarm relays

8

Filter block

4

Detectors and electronics

9

Carrier

5

Status and alarm LEDs

10

Air filter

2.2 Control Panel

The front control panel consists of:

•  Display (1)
•  Status and alarm LEDs and point ID Labels (2)
•  Keypad (3)
•  Power LED indicator (4)

CM4 Gas Monitor

1

2

3

4

Figure 2-2: Control Panel

Legend

1

Display

3

Keypad

2

Status LED and point ID labels

4

Power/Lock LED 

2.2.1 Display

The  display  is  a  1-line  by  20-character  vacuum  fluorescent  display 

that shows program and operation information.

In  the  Monitor  Mode,  if  no  gas  concentration  is  detected  and  in  the 

Idle Mode, the display brightness is reduced to 60% of full brightness. 

This feature extends the life of the vacuum fluorescent display.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

YOKOGAWA FX1000 Drawings preview
FX1000
Brand: YOKOGAWA Pages: 3
Panasonic LP-400 Series External Control Manual preview
LP-400 Series
Brand: Panasonic Pages: 180
Teac LX Series Instruction Manual preview
LX Series
Brand: Teac Pages: 148
IFM LX Series Operating Instructions Manual preview
LX Series
Brand: IFM Pages: 25
Campbell 109B Instruction Manual preview
109B
Brand: Campbell Pages: 16
C-LOGIC 8900 Instruction Manual preview
8900
Brand: C-LOGIC Pages: 4
C-lock GreenFeed Instruction Manual preview
GreenFeed
Brand: C-lock Pages: 32
C-LOGIC 8730 Instruction Manual preview
8730
Brand: C-LOGIC Pages: 12
Saluki S3602 Series User Manual preview
S3602 Series
Brand: Saluki Pages: 312
YOKOGAWA BT200 User Manual preview
BT200
Brand: YOKOGAWA Pages: 53
Flytec Element Track Quick Manual preview
Element Track
Brand: Flytec Pages: 2
Solartron Mobrey MRL800 Installation & Maintenance Manual preview
MRL800
Brand: Solartron Mobrey Pages: 34
Sekonic Litemaster Pro L-478DR Operating Manual preview
Litemaster Pro L-478DR
Brand: Sekonic Pages: 16
Keysight Technologies M9602A Configuration Manual preview
M9602A
Brand: Keysight Technologies Pages: 10
BC Biomedical USP-30 User Manual preview
USP-30
Brand: BC Biomedical Pages: 9
KERN MLS 50-3...N series Service Manual preview
MLS 50-3...N series
Brand: KERN Pages: 16
ICP DAS USA PMC series User Manual preview
PMC series
Brand: ICP DAS USA Pages: 340
Molectron ENERGY MAX EM400 User Manual preview
ENERGY MAX EM400
Brand: Molectron Pages: 40

Brands by name

Popular brands

Load more brands