manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

3-14

3.12 Loading Chemcassette

®

 Tape

For  Chemcassette

®

  loading  procedure,  see 

Section  9.2.3

  and 

9.2.4

.

 WARNING

Be sure to install the correct Chemcassette

®

. (See 

Appendix A

 for 

part number information.) Make sure the label on the Chemcassette

®

 

and the label on the analyzer correspond. Incorrect Chemcassette

®

 

replacement defeats the CM4’s ability to warn of dangerous gas 

concentrations.

NOTE:

Only one Chemcassette

®

 type should be used with each carrier.

3.13 Power On/Off

Use the rocker switch on the right rear of the unit, above the power 

cord, to turn on power to the Model CM4. For Rack Mount units, use 

the  power  panel  at  the  top  of  the  rack.   The  number  of  each  switch 

correlates to the position of the CM4 unit in the rack. 
The display shows:

CM4

Upon  power-up,  the  CM4  conducts  a  self-diagnostic  procedure  to 

check:

•  Memory
•  Hardware
•  Voltages

The display shows:

SELF TEST

CM4 V305

After  this  display,  the  Chemcassette

®

  advances  and  the  pump  turns 

on. The display shows:

STABILIZING

then

CURRENTLY MONITORING

NOTE:

The CM4 automatically attempts to enter the Monitoring Mode 

whenever it is switched on.

3.14 Installation Notice

Press PROGRAM to exit the Monitor Mode.
You must perform the following Quick-start procedure at installation 

before operating the instrument. With the Chemcassette

®

 and tubing 

installed:

1.  Access  Service  Mode  4.8  in  the  SERVICE  (4.SERVICE)  menu. 

The display will show:

PRESSURE CTS = 832

1 = PUMP   2 = LIMITS

2.  Press 1 to switch the pump on. A new pressure counts value 

will appear in the display. This is your “normal reading.”

3.  Select 2 to set the High and Low Limits.
4.  Set  the  High  Limit  value  to  the “normal  reading”  plus  52  ± 

12.

5.  Set  the  Low  Limit  value  to  the “normal  reading”  minus  52  ± 

12.

6.  When the values are set, press ENTER to store the values.

Refer to 

Section 8.9

 for more details on this procedure.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

3B6 SLIM Operator'S Manual preview
SLIM
Brand: 3B6 Pages: 30
dallmeier SMatrix DMX2400 Commissioning preview
SMatrix DMX2400
Brand: dallmeier Pages: 12
Omega DP3001 User Manual preview
DP3001
Brand: Omega Pages: 24
Lennox Smart Air Quality Monitor Installation And Setup Manual preview
Smart Air Quality Monitor
Brand: Lennox Pages: 28
Roland KR-1070 Owner'S Manual preview
KR-1070
Brand: Roland Pages: 96
Sper scientific 860031 Instruction Manual preview
860031
Brand: Sper scientific Pages: 56
Chauvin Arnoux C.A 43 User Manual preview
C.A 43
Brand: Chauvin Arnoux Pages: 44
Droplet SP2-D Operator'S Manual preview
SP2-D
Brand: Droplet Pages: 35
Sencore cm2125 Operation And Application Manual preview
cm2125
Brand: Sencore Pages: 75
truflo ULTRAFLO 5000 Operating Manual preview
ULTRAFLO 5000
Brand: truflo Pages: 33
Major tech MT 770 Instruction Manual preview
MT 770
Brand: Major tech Pages: 16
NARDA AMB-8059 Quick Step Manual preview
AMB-8059
Brand: NARDA Pages: 60
Righton Retinomax K+Screeen Instructions Manual preview
Retinomax K+Screeen
Brand: Righton Pages: 112
M&C GenTwo PMA1000V2.4 Instruction Manual preview
GenTwo PMA1000V2.4
Brand: M&C Pages: 110
Aqualytic AL10Con Instruction Manual preview
AL10Con
Brand: Aqualytic Pages: 16
SCHOTT CG 853P Operating Manual preview
CG 853P
Brand: SCHOTT Pages: 76
JETI model MVario Quick Start Manual preview
MVario
Brand: JETI model Pages: 6
ADCMT 12704A Operation Manual preview
12704A
Brand: ADCMT Pages: 28

Brands by name

Popular brands

Load more brands