manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

E-31

E.7 Serial Device Applications

The  serial  interface  is  designed  for  unidirectional  communication  from 

a CM4 monitor to a single printer or other remote device. It is possible, 

therefore, that the application for this interface requires connection to a 

remote device other than the printer options described in this appendix.

 CAUTION

Cabling used between the CM4 monitor and the external device must 

be shielded and properly grounded to maintain reliable operation and 

control RF emissions and susceptibility

For these applications, note the pin-out configuration in each of the diagrams.

Multiple CM4 monitors and a single computer

CM4

Monitor

COM2

CM4

Monitor

COM2

CM4

Monitor

COM2

CM4

Monitor

COM2

Female DB-9

on CM4

TX  2

RX  3

Signal Gnd  5

Cable Pinout

Computer with multiple

Communication Ports

Interface

RS-232 P/N 874022-R Rear Panel Mount

Jumpers

See 

Section D.2

 for DCE settings

Computer Port Customer-supplied RS-232C; check user device for compatibility before 

ordering.

Cable

User-supplied. Refer to diagram for pin-out configuration.

Also, refer to the EMC Considerations section on page 

D-2

.

Protocol

Customer-written per information in Appendix E.

Note

Maximum range: 50 Ft.

Figure E-1: Serial Interface, Multiple CM4s, Single Computer, Unidirectional 

Communications

Multiple CM4 monitors and a single computer

Bi-Directional Communication up to 4000 ft distance

CM4

Monitor

RS-422

CM4

Monitor

RS-422

CM4

Monitor

RS-422

CM4

Monitor

RS-422

Computer with multiple

Communication Ports

Female DB-25

Male DB-9

25   TXD+

19   TXD-
15   RXD-
17   RXD+

RXD+  2

RXD-  3

TXD-  4

TXD+  8

Cable Pinout

Ground  7

1    Ground

For ground, use another conductor in the cable;

do not use the shield or drain wire

Interface

RS-232 P/N 874024-R Rear Panel Mount

Computer Port Customer-supplied; check user device for compatibility before ordering.
Cable

User-supplied. Refer to diagram for pin-out configuration.

Also, refer to the EMC Considerations section on page 

D-2

.

Protocol

Customer-written per information in Appendix E.

Note

Maximum range: 4000 Ft.

Figure E-2: Bidirectional Communication, Single Computer, Multiple CM4s 

up to 4000 ft distance.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

QLA KT2 Operating Instructions Manual preview
KT2
Brand: QLA Pages: 18
FCI ST100 series Operation Manual preview
ST100 series
Brand: FCI Pages: 44
FCI ST100 series Manual preview
ST100 series
Brand: FCI Pages: 36
FCI ST100 series Configuration Software Manual preview
ST100 series
Brand: FCI Pages: 26
QMI TRIPLEX Manual preview
TRIPLEX
Brand: QMI Pages: 54
Navman A300 Sport.Tool Specification preview
A300 Sport.Tool
Brand: Navman Pages: 1
Vanguard Instruments Company WRM-10P User Manual preview
WRM-10P
Brand: Vanguard Instruments Company Pages: 62
Vanguard Instruments Company IRM-5000P User Manual preview
IRM-5000P
Brand: Vanguard Instruments Company Pages: 58
+GF+ MSA 2 MULTI Instruction Manual preview
MSA 2 MULTI
Brand: +GF+ Pages: 64
+GF+ GF 3-2630-X Manual preview
GF 3-2630-X
Brand: +GF+ Pages: 12
+GF+ Signet 4630 Operating Instructions Manual preview
Signet 4630
Brand: +GF+ Pages: 48
Metretek MTEK6000 Series User Manual preview
MTEK6000 Series
Brand: Metretek Pages: 81
janitza UMG 96-PA User Manual preview
UMG 96-PA
Brand: janitza Pages: 85
MULTISPAN AMP-23 Operating Manual preview
AMP-23
Brand: MULTISPAN Pages: 4
X-Rite DensiEye 700 Quick Start Manual preview
DensiEye 700
Brand: X-Rite Pages: 130
Laserworld GREEN-4000 532 Manual preview
GREEN-4000 532
Brand: Laserworld Pages: 5
XS Instruments 70 Vio Series Instruction Manual preview
70 Vio Series
Brand: XS Instruments Pages: 41
B meters HYDROSONIS-UP Operating And Installation Instructions preview
HYDROSONIS-UP
Brand: B meters Pages: 3

Brands by name

Popular brands

Load more brands