Honeywell CM4 Technical Handbook Download Page 107

Page: 107 / 202

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

9-12

9.5 Cleaning the Chemcassette

Optics

See Figures 9-10 and

9-11

Clean Chemcassette

optics annually or whenever an optics verification

error occurs.
Instructions

1. Turn off power to the CM4.
2. Open the tape load lever and remove the Chemcassette

carrier.

3. Unscrew two screws on the top panel and lift it. The panel

pivots on studs as shown in Figure 9-10.

4. Tighten the retaining knob to hold the panel open.
5. Release, then remove the pressure transducer port tubing from

the optics block (see

Figure 9-11

NOTE:

Remove and clean one port at a time to ensure proper orientation

of tubing. Do not remove the capillary tubing (microtubing).

6. Insert the tube of a small can of compressed air for optics

cleaning into the port and spray for three or four seconds.

7. Reconnect the pressure transducer port tubing. Repeat steps

4, 5 and 6 for remaining ports.

CAUTION

Failure to replace and retighten hardware after servicing can adversely

affect instrument performance and electromagnetic radiation

compliance (EMC). Make certain all fasteners are reinstalled and

firmly tightened. This will ensure a proper ground.

8. Close the panel and secure it with the screws.
9. Load the Chemcassette

carrier and close the load lever.

10. Turn on power to the CM4.

Figure 9-10: Accessing Chemcassette

Optics

Legend

Lift top panel

Studs

Tighten retaining knob on inside panel

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands

Honeywell CM4, Technical Handbook

Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands