manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

vii

Table of Contents

8.2 Function 4.1 – Relay/LED Test  ............................................................... 8-2
8.3 Alarm Tests .................................................................................................... 8-3

8.3.1 Function 4.2.1-Alarm Indicator Test .......................................... 8-3
8.3.2 Function 4.2.2-Simulated Alarm Test ....................................... 8-3
8.3.3 Function 4.2.3-Optics Alarm Test ............................................... 8-5

8.4 Function 4.3 – Diagnostics ...................................................................... 8-7
8.5 Function 4.4 – Reset System ................................................................... 8-8
8.6 Function 4.5 – Load Chemcassette

®

/Filter Change ..............................................8-8

8.7 Function 4.6 – Set Flow ..........................................................................8-11
8.8 Function 4.7 – MDA Service ..................................................................8-12
8.9 Function 4.8 – Pump Limits ..................................................................8-12

8.9.1 Operation .........................................................................................8-12
8.9.2 Set-up ................................................................................................8-12

8.10 Function 4.9 – Reboot ..........................................................................8-13

9 Maintenance

9.1 Introduction ................................................................................................. 9-2
9.2 Chemcassette

®

 Maintenance .................................................................. 9-2

9.2.1 Remove Carrier ................................................................................ 9-2
9.2.2 Verify Optics ...................................................................................... 9-4
9.2.3 Loading the Carrier ......................................................................... 9-5
9.2.4 Installing the Chemcassette

® ...................................................................................................9-6

9.2.5 Checking Flowrates ........................................................................ 9-7

9.3 Filter Maintenance ..................................................................................... 9-8

9.3.1 CM4 Internal Filter Replacement Procedure ......................... 9-9
9.3.2 Sample Line Particulate Filter ...................................................9-10
9.3.3 CM4-P Filter Maintenance ..........................................................9-10

9.4 Fuse Replacement ....................................................................................9-11

9.4.1 AC Line Fuse ....................................................................................9-11

9.5 Cleaning the Chemcassette

®

 Optics ...................................................9-12

9.6 Installing Microtube Assembly ............................................................9-13

10 Options

10.1 Communications Options ...................................................................10-2

10.1.1 Serial Communications ............................................................10-2
10.1.2 Printers ...........................................................................................10-2

10.2 Remote Alarm Reset Option ..............................................................10-2

10.2.1 How it Works.................................................................................10-2
10.2.2 Wiring Considerations ...............................................................10-3
10.2.3 Using an External Power Supply ...........................................10-3
10.2.4 Using the CM4 Monitor’s Internal Power Supply .......................10-3

10.3 Sample Line Integrity Option ............................................................10-5

A Specifications

A.1 Introduction .................................................................................................A-2
A.2 Filter Compatibility ....................................................................................A-2
A.3 General Specifications ..............................................................................A-3

A.3.1 CM4 ......................................................................................................A-3
A.3.2 CM4-P ..................................................................................................A-3

A.4 Transport Times ..........................................................................................A-4

B Fault Listing

B.1 Fault Codes ...................................................................................................B-2
B.2 Leak Check Procedure ..............................................................................B-8

C Chemcassette

®

 Detectable Gases

D Printer Options

D.1 Overview ...................................................................................................... D-2

D.1.1 RS-232C ............................................................................................. D-2
D.1.2 RS-422 ................................................................................................ D-2
D.1.3 Desktop Printer .............................................................................. D-2

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Cablescan 90 Series Reference Manual preview
90 Series
Brand: Cablescan Pages: 58
OHAUS ST300 Instruction Manual preview
ST300
Brand: OHAUS Pages: 26
Flytec Element Track Quick Manual preview
Element Track
Brand: Flytec Pages: 2
Burkert FLOWave S 8098 Operating Instructions Manual preview
FLOWave S 8098
Brand: Burkert Pages: 192
Schneeberger MINIRAIL Manual preview
MINIRAIL
Brand: Schneeberger Pages: 35
janitza UMG 96-PA User Manual preview
UMG 96-PA
Brand: janitza Pages: 85
Leica DISTOTM D5 Quick Start preview
DISTOTM D5
Brand: Leica Pages: 2
MATO DIGIMET E30 Preset Operating Instructions Manual preview
DIGIMET E30 Preset
Brand: MATO Pages: 20
PICO TA167 User Manual preview
TA167
Brand: PICO Pages: 2
Omicron CMC 156 Reference Manual preview
CMC 156
Brand: Omicron Pages: 76
Galileo Milano 3G Owner'S Manual preview
Milano 3G
Brand: Galileo Pages: 30
NARDA SRM-3006 Operating Manual preview
SRM-3006
Brand: NARDA Pages: 240
Zhengzhou Minghe Electronic Technology LC200A User Manual preview
LC200A
Brand: Zhengzhou Minghe Electronic Technology Pages: 7
Oceanic DATATRANS Owner'S Manual preview
DATATRANS
Brand: Oceanic Pages: 114
LI-COR LI-7820 Instruction Manual preview
LI-7820
Brand: LI-COR Pages: 92
wattwatchers A6M+One Installation Manual preview
A6M+One
Brand: wattwatchers Pages: 14
H&B LDU 179.1 Technical Manual preview
LDU 179.1
Brand: H&B Pages: 45
Hanna Instruments HI96101C Instruction Manual preview
HI96101C
Brand: Hanna Instruments Pages: 48

Brands by name

Popular brands

Load more brands