manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

6-2

6.1 Introduction

The  Review  Menu  contains  eight  functions  which  permit  viewing 

data.  It  is  not  possible  to  change  the  CM4  configuration  with  these 

functions. 

2 REVIEW MENU

  

2.1  

  ALARM HISTORY

  

2.2  

  FAULT HISTORY

  

2.3  

  CURRENT TWA

  

2.4  

  LAST POWER DOWN

  

2.5  

  CUSTOMER DATA

  

2.6  

  PRINT CONFIGURATION

  

2.7  

  INST. SER. NUMBER

  

2.8  

  PRINT MENU

Figure 6-1: Review Mode Menu

The following is an overview of each of the eight options. The following 

sections describe each of these options in detail:

•  2.1  ALARM  HISTORY  displays  and  prints  up  to  16  gas  alarms 

with the most recent alarm shown first (see Section 6.2)

•  2.2 FAULT HISTORY displays and prints up to eight faults with 

the most recent shown first (see 

Section 6.3

)

•  2.3  CURRENT  TWA  displays  and  prints  the  current  Time 

Weighted  Average  (TWA)  for  each  point  that  has  been 

monitored  since  the  start  of  the  current  8-hour TWA  (see 

Section 6.4

)

•  2.4  LAST  POWER  DOWN  displays  the  most  recent  power-

down and power-up date and time (see 

Section 6.5

)

•  2.5  CUSTOMER  DATA  displays  customer  name  and  location 

(see 

Section 6.6

)

•  2.6  PRINT  CONFIGURATION  prints  the  programmed 

configuration for the system (see 

Section 6.7

)

•  2.7  INST.  SER.  NUMBER  displays  CM4  serial  number  (see 

Section 6.8

)

•  2.8 PRINT MENU prints the CM4 menu options (see 

Section 6.9

)

6.2 Function 2.1 – Alarm History

Use the alarm history function to print or display up to a maximum of 

16 gas alarms with the most recent alarm shown first. 

6.2.1 Print Alarm History

If the CM4 is equipped with a printer, see 

Figure 6-2

 for an example 

of a typical alarm history printout.
Purpose
The printout of the alarm history shows the most recent alarm first for 

up to 16 total alarms. The printout shows:

•  Instrument serial number
•  Current date and time
•  Customer name and location
•  Point number
•  Alarm date and time
•  Concentration in ppb or ppm
•  Alarm levels

Instructions

1.  Press PROGRAM to exit Monitor Mode.
2.  At  the  REVIEW  MENU  display,  press  1  or  RIGHT  ARROW  and 

ENTER to select alarm history.

The display reads:

1 – ALARM HISTORY

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

3M Charge Analyzer 711 Operating Instructions Manual preview
Charge Analyzer 711
Brand: 3M Pages: 24
Felix Instruments F-940 Operation Manual preview
F-940
Brand: Felix Instruments Pages: 102
Hach POCKET COLORIMETER II User Manual preview
POCKET COLORIMETER II
Brand: Hach Pages: 188
National Instruments PXIe-5763 Getting Started Manual preview
PXIe-5763
Brand: National Instruments Pages: 15
Gas Data GFM 436 User Manual preview
GFM 436
Brand: Gas Data Pages: 99
Keithley 6487 Reference Manual preview
6487
Brand: Keithley Pages: 338
AXE MM2 Series Operation Manual preview
MM2 Series
Brand: AXE Pages: 5
BUSCH VACTEST GCD 200 Instruction Manual preview
VACTEST GCD 200
Brand: BUSCH Pages: 12
Omega PX2088 User Manual preview
PX2088
Brand: Omega Pages: 59
YOSensi YO Distance User Manual preview
YO Distance
Brand: YOSensi Pages: 27
Scheppach 88001955 Translation From The Original Instruction Manual preview
88001955
Brand: Scheppach Pages: 20
Quadelectra Audioworx L1mDrum Operation Manual preview
L1mDrum
Brand: Quadelectra Audioworx Pages: 12
sewerin EX-TEC Combi Operating Instructions Manual preview
EX-TEC Combi
Brand: sewerin Pages: 134
Teledyne Lecroy Quantumdata 780E Quick Start Manual preview
Quantumdata 780E
Brand: Teledyne Lecroy Pages: 12
Danfoss PR-SC4K Direct Installation Manual preview
PR-SC4K Direct
Brand: Danfoss Pages: 2
ScienTECH NTEP Quick Start Manual preview
NTEP
Brand: ScienTECH Pages: 18
DISTELL Torrymeter User Manual preview
Torrymeter
Brand: DISTELL Pages: 53
Seascape NOVASUB DDG-P Quick Start Manual preview
NOVASUB DDG-P
Brand: Seascape Pages: 2

Brands by name

Popular brands

Load more brands