manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

viii

Table of Contents

D.1.4 Enclosure Printer Kit ..................................................................... D-2
D.1.5 Printer Share Box ........................................................................... D-2

D.2 Jumpers ........................................................................................................ D-3
D.3 Cabling .......................................................................................................... D-4

D.3.1 EMC Considerations ..................................................................... D-4
D.3.2 Cabling Diagrams .......................................................................... D-5

D.4 Instructions and Checklist ..................................................................... D-7
D.5 Other Applications ................................................................................... D-9

E Serial Communications Protocol

E.1 Introduction ................................................................................................. E-2
E.1.1 Overview .................................................................................................... E-2
E.1.2 Communication Port ............................................................................. E-2
E.1.3 Set up Procedure ..................................................................................... E-3
E.1.4 Protocol Specifics .................................................................................... E-3

Data and Packets ....................................................................................... E-3
Checksum (Check Character) ................................................................ E-4
ACK/NAK Handshake ............................................................................... E-4

E.2 Protocol Packet Definition ....................................................................... E-5
E.2.1 Packet Format  

 .......................................................................... E-5

Start Code ..................................................................................................... E-5
Receiver Address ........................................................................................ E-5
Transmitter Address .................................................................................. E-5
Length ........................................................................................................... E-5
Command..................................................................................................... E-5
Data ................................................................................................................ E-5
Checksum ..................................................................................................... E-5

E.2.2 Generic Data Formats ............................................................................ E-6

Date Format ................................................................................................. E-6

Time Format ................................................................................................ E-6
Date/Time Examples ................................................................................ E-6
Concentration Data Format Code ....................................................... E-6

E.3 Protocol Command Definition ............................................................... E-7
E.3.1 Status and Query Commands............................................................. E-7

NOP - 0x28 ................................................................................................... E-7
Get System Information - 0x30 ............................................................. E-7
Get Unit Status - 0x31 .............................................................................. E-8
Get Idle Time - 0x32 ................................................................................E-10
Get Date & Time - 0x33 ..........................................................................E-10
Get Maintenance Dates - 0x34 ............................................................E-10
Get Point Configuration - 0x35 ...........................................................E-11
Get Alarm History - 0x36 .......................................................................E-11
Get Current Point Status - 0x37 ..........................................................E-12
Get TWA Time - 0x38 ..............................................................................E-12
Get Display Cycle Time - 0x39   ........................................................E-12
Get the Number of Gas Tables Available - 0x3A ...........................E-13
Get Printer Setup - 0x3B ........................................................................E-13
Get Gas Table Data - 0x3C .....................................................................E-13
Get Fault History - 0x3D ........................................................................E-14
Get K-Factor - 0x3E ..................................................................................E-14
Get Pyrolyzer Temperatures - 0x42 ...................................................E-15
Get Pump Limits - 0x43 .........................................................................E-15
Get Filter Life - 0x44 ................................................................................E-15
Get Floating Status - 0x45 ....................................................................E-16
Get One Alarm - 0x47  ............................................................................E-17

E.4 Configuration and Directive Commands .........................................E-17

Set K-Factor - 0x50 ...................................................................................E-17

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

GE Mentor Visual iQ Quick Start Manual preview
Mentor Visual iQ
Brand: GE Pages: 2
Van Walt KISS Quick Start Manual preview
KISS
Brand: Van Walt Pages: 6
zebris PDM Specification And Operating Instructions preview
PDM
Brand: zebris Pages: 42
Kamstrup MULTICAL 62 Technical Description preview
MULTICAL 62
Brand: Kamstrup Pages: 100
Kamstrup MULTICAL 41 Installation And User Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 41 Installation Manual preview
MULTICAL 41
Brand: Kamstrup Pages: 12
Kamstrup flowIQ 3100 Technical Description preview
flowIQ 3100
Brand: Kamstrup Pages: 60
Kamstrup MULTICAL 403 Technical Description preview
MULTICAL 403
Brand: Kamstrup Pages: 136
Kamstrup ULTRAFLOW 54 Installation Manual preview
ULTRAFLOW 54
Brand: Kamstrup Pages: 16
Kamstrup MULTICAL 603 Technical Description preview
MULTICAL 603
Brand: Kamstrup Pages: 155
M-system 47LCT Operating Manual preview
47LCT
Brand: M-system Pages: 16
M-system 73VR3100 Startup Manual preview
73VR3100
Brand: M-system Pages: 25
OHAUS Defender T24PE Instruction Manual preview
Defender T24PE
Brand: OHAUS Pages: 32
Magtrol 6510e User Manual preview
6510e
Brand: Magtrol Pages: 76
Flexim 990735-1 User Manual preview
990735-1
Brand: Flexim Pages: 160
Neriox 111456 Operating Instructions Manual preview
111456
Brand: Neriox Pages: 10
E+H Micropilot S FMR533 Manual preview
Micropilot S FMR533
Brand: E+H Pages: 12
National Instruments AT-AI-16XE-10 Programmer'S Manual preview
AT-AI-16XE-10
Brand: National Instruments Pages: 169

Brands by name

Popular brands

Load more brands