Honeywell CM4 Technical Handbook Download Page 97

Page: 97 / 202

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

9-2

9.1 Introduction

The Maintenance Section includes:

• Chemcassette

Maintenance covers the Chemcassette

Chemcassette

carrier, optics verification, and flowrate check

(Section 9.2)

• Filter maintenance covers the replacement of CM4 filters

(

Section 9.3

)

• Fuse replacement (

Section 9.4

)

• Cleaning Chemcassette

optics (

Section 9.5

)

• Installing Microtube assemblies (

Section 9.6

)

NOTE:

Prior to performing any maintenance procedure, leave Monitor

Mode. (See

Section 4.5.1

CAUTION

For system integrity, always perform a leak test after any maintenance

procedure. See

Section B.2

for leak check procedure.

9.2 Chemcassette

Maintenance

This section describes maintenance and handling procedures for the

Chemcassette

and the Chemcassette

carrier.

Perform the following functions when replacing a Chemcassette

tape:

•  Remove carrier
•  Verify optics
•  Load new Chemcassette

in carrier

• Install Chemcassette

• Check flowrates

9.2.1 Remove Carrier

To remove the Chemcassette

carrier from the CM4:

1. Press PROGRAM to exit Monitor Mode.
2. From the 4–SERVICE MENU, Choose the subfunction 5–LOAD

Chemcassette

4 – SERVICE MODE

5 – LOAD Chemcassette

If Chemcassette

counter is disabled, proceed to step 6. If

Chemcassette

counter is enabled, the screen displays:

RESET COUNTER 1=Y

3. Press either:

• 1 to re-initialize the counter so that the display shows a fault

when less than 24 hours of Chemcassette

remains

• 0 to continue without resetting counter

If the internal filter timer is active (see

Section 7.8.2

), the screen

displays:

INT FILTER RESET 1=Y

4. Press either:

• 1 to reset the timer after servicing the filters (see

Section

9.3

)

• 0 to continue without resetting timer

If the external filter timer is active (see

Section 7.8.3

) , the screen

displays:

EXT FILTER RESET 1 = Y

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands

Honeywell CM4, Technical Handbook

Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands