Honeywell CM4 Technical Handbook Download Page 104

Page: 104 / 202

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

9-9

9.3.1 CM4 Internal Filter Replacement Procedure

See Figure 9-6

Figure 9-6: Filter Maintenance

Legend

Filter block

Particulate Filters

Filter block handle

Acid scrubbing filter

Gray ring

The Model CM4 will use one of the filter blocks shown in Figure 9-7.

Note the positions of the filters for your type of filter block. The filter

block is keyed to fit only one way into the instrument.

Vacuum

Acid

Chamfer

Acid

Filter Assembly Type 1:

Filter Assembly Type 2:

Figure 9-7: Filter Block Orientation

The following steps apply to all filters located within the CM4. Refer

to these steps when performing maintenance on any filters in the

system.

1. Open the tape load lever to the servicing position.
2. On older model CM4’s, release carrier retaining clip by pressing

toward rear of unit.

3. Remove the Chemcassette

carrier by placing your fingers

under it, palms up, and lifting straight up. See

Figure 9-1

for

proper procedure.

NOTE:

To avoid carrier torque and damage, do not tilt the carrier. Contact

Honeywell Analytics if you are unable to remove the carrier.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands

Honeywell CM4, Technical Handbook

Search results

Summary of Contents for CM4

Reviews:

Related manuals for CM4

Brands by name

Popular brands