manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

4-7

4.5.1 Programming by Scrolling

1.  Press PROGRAM to exit Monitor Mode. The display reads:

END MONITOR? 1=Y 0=N

2.  Press 1 to end the monitoring session. The display reads:

SELECT PROGRAM 

 

 indicates further menu choices are available.

3.  Press  CURSOR  ARROW  LEFT/RIGHT  to  scroll  forward/

backward through the four mode (menu) choices. The display 

shows modes preceded by a one-digit number.

1 – CALIBRATION MODE

2 – REVIEW MODE

3 – SETUP MODE

4 – SERVICE MODE

4.  Press  ENTER  when  the  display  shows  the  desired  mode 

selection. Depending on the entry, the CM4 displays the menu 

(subfunction) choices.

                     CALIBRATION MODE 

                         REVIEW MENU 

                           SETUP MENU 

                         SERVICE MENU 

5.  If the option includes additional functions, the display shows 

  .  Press  CURSOR  ARROW  LEFT/RIGHT  to  display 

menu options.

6.  Press ENTER.

4.5.2 Programming Using Direct Numeric Entry

Refer  to  the  menu  structure  in  Section  4.6. To  select  an  item  using 

direct numeric entry:

1.  Press PROGRAM to exit Monitor Mode. The display reads:

END MONITOR? 1=Y 0=N

2.  Press  1  within  two  seconds  to  end  monitoring.  If  the  printer 

option is available, the display reads:

PRINT TWA  1=Y   0=N

3.  Press 1 to print TWA information. Entering 0 exits without 

printing TWA information. 

After selecting 1, the display advances to:

SELECT PROGRAM  

 indicates further menu choices are available.

4.  Press  the  numeric  key  corresponding  to  the  menu  numbers, 

functions,  and  points  (see 

Section  4.6

  for  complete  menu 

listing).  For  example,  to  select  the  alarm  history  for  Point  3, 

press the following in sequence:

•  2 (to access the Review Mode)
•  1 (to access Alarm History)
•  3 (to specify Point 3)

NOTE:

The following sections describe accessing menus and functions 

using the scrolling method and function keys. Once you become 

familiar with the menu structure, you will be able to access 

menus and functions more quickly using direct numeric entry 

rather than using the scrolling and function key method. 

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Eaton CMD Manual preview
CMD
Brand: Eaton Pages: 43
VEE GEE BX-3 Operation Manual preview
BX-3
Brand: VEE GEE Pages: 2
Valcom V9992 Datasheet preview
V9992
Brand: Valcom Pages: 1
King Instrument 7710 Series Installation Instructions preview
7710 Series
Brand: King Instrument Pages: 5
CryptOn CCP700-B-EN560 Manual preview
CCP700-B-EN560
Brand: CryptOn Pages: 13
Kane KANE958 Manual preview
KANE958
Brand: Kane Pages: 36
Parker SensoControl ServiceJunior Operating Instructions Manual preview
SensoControl ServiceJunior
Brand: Parker Pages: 18
Badger Meter Vortex VN2000 User Manual preview
Vortex VN2000
Brand: Badger Meter Pages: 12
Brigade Backsense BS-9000-WD Installation And Operating Manual preview
Backsense BS-9000-WD
Brand: Brigade Pages: 42
Cargo Data Boomerang 2 Use Instructions preview
Boomerang 2
Brand: Cargo Data Pages: 3
GeoMax Zoom90 Installation Manual preview
Zoom90
Brand: GeoMax Pages: 14
Rodgers Exeter 770 Manual preview
Exeter 770
Brand: Rodgers Pages: 54
Fluke Biomedical Victoreen 07-494 Operator'S Manual preview
Victoreen 07-494
Brand: Fluke Biomedical Pages: 34
JPT Seal-355-3 User Manual preview
Seal-355-3
Brand: JPT Pages: 19
Samson 024.85 Translation Of The Original Operating Instruction preview
024.85
Brand: Samson Pages: 61
Ulvac SWU10-U Instruction Manual preview
SWU10-U
Brand: Ulvac Pages: 39
UEi Smart Bell PLUS Instruction Manual preview
Smart Bell PLUS
Brand: UEi Pages: 16
Ocean Reef NEPTUNE SPACE PREDATOR Owner'S Manual preview
NEPTUNE SPACE PREDATOR
Brand: Ocean Reef Pages: 24

Brands by name

Popular brands

Load more brands