manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

D-5

D.3.2 Cabling Diagrams

The following diagrams show the cabling configurations for single and 

multiple CM4 monitors connecting to one of the printer options. The 

cabling is identical for both desktop and rack mount installations.

 CAUTION

Cabling used between the CM4 monitor and the external device must 

be shielded and properly grounded to maintain reliable operation and 

control RF emissions and susceptibility.

Single CM4 monitor and printer

CM4

Monitor

COM2

Printer

Interface

RS-232 P/N 874201-R Rear Panel Mount

Jumpers

See 

Section D.2

 for DCE jumper settings

Cable

For  configurations  with  the  Rack  Mount  Printer  located  in  the  same 

rack  cabinet  as  the  CM4  monitor,  the  interface  cable  (P/N  1874-0037, 

9-pin to 25-pin, 10 ft.) is supplied. For distances to 50 ft. between the 

CM4 monitor and the Rack Mount Printer, order cable separately (P/N 

1874-0031, 9-pin to 25-pin, 50 ft.).
With  the  Desktop  Printer,  a  10  ft.  interface  cable  is  supplied  (for 

connection between the CM4 monitor and the Desktop Printer).
For customer-supplied cables, refer to the EMC Considerations section 

on page 

D-2

.

Printer

P/N 874012 Desktop or P/N 1874-0005 Rack Mount.
These  are  115 VAC  printers.  Other  voltages  for  printers  (rack  mount 

only) are available as MVIP.

Notes

1.  Maximum range: 50 Ft.
2.  For Rack Mount Printer, set the printer switch to RS-232.

Figure D-3: Serial Interface, Single CM4, Single Printer

2 to 5 CM4 monitors and a single printer

CM4

Monitor

COM2

CM4

Monitor

COM2

CM4

Monitor

COM2

CM4

Monitor

COM2

CM4

Monitor

Printer

Share Box

Printer

COM2

6

1

Interface

RS-232 P/N 874201-R Rear Mount

Jumpers

See 

Section D.2

 for DTE settings

Cables

The Printer Share Boxes listed on this page include the following 

cables:
P/N 1874-0037 9-pin to 25-pin, 10 ft., qty 5, for connection between 

CM4 Monitors and Printer Share Box
P/N 1991-0027 25-pin to 25-pin, 6 ft., qty 1, for connection between 

the Printer Share Box and Printer.
For applications requiring a 50 ft. cable between the CM4 monitor 

and the Printer Share Box, order cables separately (P/N 1874-0031, 

9-pin to 25-pin, 50 ft.).
The Desktop Printer includes a 10 ft. interface cable for connection 

between the Printer Share Box and the Desktop Printer.
For customer-supplied cables, refer to the EMC Considerations 

section on page 

D-2

.

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Danfoss 40 Calibration Instruction preview
40
Brand: Danfoss Pages: 8
Yamaha AW2816 Tutorial preview
AW2816
Brand: Yamaha Pages: 31
YOKOGAWA SC21 Series Instruction Manual preview
SC21 Series
Brand: YOKOGAWA Pages: 16
Neogen Corporation AccuPoint 2 ATP Manual preview
AccuPoint 2 ATP
Brand: Neogen Corporation Pages: 16
Van Walt Aquaread Quick Start Manual preview
Aquaread
Brand: Van Walt Pages: 2
horiba TW-100 Instruction Manual preview
TW-100
Brand: horiba Pages: 175
Teledyne Lecroy BPA Quick Start Manual preview
BPA
Brand: Teledyne Lecroy Pages: 3
NIEUWKOOP EC-95 Quick Manual preview
EC-95
Brand: NIEUWKOOP Pages: 2
Rubicson 48829 Manual preview
48829
Brand: Rubicson Pages: 4
QEED QI-POWER-485-300-LV Instruction Manual preview
QI-POWER-485-300-LV
Brand: QEED Pages: 2
Xylem WTW pH/ION 3310 Quick Start Manual preview
WTW pH/ION 3310
Brand: Xylem Pages: 48
J-TECH Solar Auxiliary Power Unit Operator'S Manual preview
Solar Auxiliary Power Unit
Brand: J-TECH Pages: 6
Lumel NA3 User Manual & Quick Start preview
NA3
Brand: Lumel Pages: 32
Televes H30FLEX 593302 Quick Manual preview
H30FLEX 593302
Brand: Televes Pages: 2
INTERSPIRO Divator Pro User Manual preview
Divator Pro
Brand: INTERSPIRO Pages: 76
Net2Edge LIB-304 Installation Manual preview
LIB-304
Brand: Net2Edge Pages: 37
Ega Master MASTERVISION ECO Operating Instructions Manual preview
MASTERVISION ECO
Brand: Ega Master Pages: 48
Samson MDR10 Owner'S Manual preview
MDR10
Brand: Samson Pages: 28

Brands by name

Popular brands

Load more brands