manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

9-10

4.  Grasp the filter block handle (2) and pull out.
5.  The  filters  are  attached  with  a  quick  disconnect  connector. 

Remove  the  filter  by  pressing  the  gray  ring  (3)  against  the 

fitting and sliding the filter out of the fitting.

6.  Install the new filters by fully inserting the fittings. Filters have 

an arrow on the filter body indicating the direction of flow. The 

arrows should point toward the filter block. Be sure to orient 

the filters correctly

7.  Reinstall the filter block (1).
8.  Reinstall  the  Chemcassette

®

  carrier  and  close  the  tape  load 

lever.

9.3.2 Sample Line Particulate Filter

Sample  line  particulate  filters  prevent  dust  from  entering  through 

the  sample  line.  Particulate  filters  are  not  recommended  for 

all  applications.  See 

Appendix  A

  for  compatibility  information. 

Replace the sample filter every three to twelve months.
Remove  the  old  filter  from  the  end  of  the  sample  line  and  attach  a 

new filter. Install the filter so the arrow on the side of the filter points 

toward the CM4 tubing.

9.3.3 CM4-P Filter Maintenance

 CAUTION

The pyrolyzer operates at a very high temperature. Before performing 

any service on the instrument, always wait 30 minutes after switching 

off power to allow the pyrolyzer to cool.

The  filter  block  in  the  Model  CM4-P  is  physically  larger  than  the 

block  in  the  standard  Model  CM4  (See  Figure  9-8).  Removing  the 

filter  block  is  the  same  as  described  in 

Section  9.3.1

,  Internal  Filter 

Replacement.

Figure 9-8: CM4-P Filter Block

There are nine filters in the CM4-P filter block: four charcoal for Freon

®

 

removal, four particulate, and one acid scrubber. The acid scrubber and 

particulate filters are identical to the standard Model CM4. The charcoal 

filters have a part number unique to the CM4-P: P/N 1874-0139. These 

filters are not interchangeable with other charcoal filters for removing 

Freon, such as those used on System 16.
Note  the  flow  direction  arrow  when  replacing  the  charcoal  and 

particulate filters:

•  Freon filters: arrow points away from the removable filter 

block

•  Particulate filters: arrow points toward the removable filter 

block

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Valeport 803 Operating Manual preview
803
Brand: Valeport Pages: 25
RayTek GP Series Operating Instructions Manual preview
GP Series
Brand: RayTek Pages: 72
Magnetrol A10 Installation And Operating Manual preview
A10
Brand: Magnetrol Pages: 40
Larson Davis System 824 Reference Manual preview
System 824
Brand: Larson Davis Pages: 536
TA Instruments Q1000 Manual preview
Q1000
Brand: TA Instruments Pages: 7
Velleman DCM120 User Manual preview
DCM120
Brand: Velleman Pages: 96
Icon Process Controls Level Pro UltraPro 500 Series Instruction Manual preview
Level Pro UltraPro 500 Series
Brand: Icon Process Controls Pages: 19
BYK micro-TRI-gloss ? Operating Instructions Manual preview
micro-TRI-gloss ?
Brand: BYK Pages: 174
Fora GTel Owner'S Manual preview
GTel
Brand: Fora Pages: 64
Kreg Precision KMS7101 Instructional Manual preview
Precision KMS7101
Brand: Kreg Pages: 16
FuzzDog Quack Machine Quick Start Manual preview
Quack Machine
Brand: FuzzDog Pages: 6
Waves GRAND RHAPSODY PIANO User Manual preview
GRAND RHAPSODY PIANO
Brand: Waves Pages: 19
DeFelsko PosiTector BHI Manual preview
PosiTector BHI
Brand: DeFelsko Pages: 25
Ofs udox Operating Instructions Manual preview
udox
Brand: Ofs Pages: 28
Hach DOC026.52.00769 User Manual preview
DOC026.52.00769
Brand: Hach Pages: 64
TDE Instruments Digalox DPM72-MPPA Instruction Manual preview
Digalox DPM72-MPPA
Brand: TDE Instruments Pages: 8
DigiTech AT Wizard M5 Manual preview
AT Wizard M5
Brand: DigiTech Pages: 11
Micromeritics DVVA II 4000 Operator'S Manual preview
DVVA II 4000
Brand: Micromeritics Pages: 254

Brands by name

Popular brands

Load more brands