manualshive.com logo in svg

Honeywell CM4, Technical Handbook

The Sealey CM4 is a versatile and user-friendly tool that requires a Quick Start Manual for effective usage. Our website offers a free download of this manual, ensuring convenient access for users. Discover the full potential of the Sealey CM4 by downloading the manual from manualshive.com.

Share
Download
background image

CM4 Four-Point Continuous Monitor

CM4 Technical Manual

1-8

1.7 Instrument Diagnostics

The  CM4  provides  diagnostic  instrument  fault  and  maintenance 

requirement indications. These activate one of the following:

•  One or both fault relays activate
•  On-board  memory  stores  most  recent  eight  fault  events  for 

later recall

•  Fault information is sent to the printer (if enabled)
•  Status  LEDs  light  yellow  for  the  appropriate  point  to  indicate 

instrument faults

•  The display shows the fault information
•  If  the  fault  generated  is  an  instrument  fault  and  the  CM4  is 

appropriately configured, the current level on the optional analog 

4-20 mA output port is reduced to 2 mA.

Condition

Point

Status LED

Point

Alarm LED

Relays

Activated

Beeping

Audio Alarm

Display

Monitoring

Green

OFF

All OFF

OFF

Current concentrations (each point displayed for four 

seconds)

Level 1 alarm

Green

Red 

(steady)

- Low level alarm for affected point

- General low level alarm

ON

Current concentrations

Level 2 alarm

Green

Flashing 

red

- High and low level alarms for 

affected point

- General high and low level alarms

ON

Current concentrations

Low Chemcassette maintenance fault (monitoring continues) 

(See 

Appendix B

)

Green

OFF

Maintenance fault

OFF

Current concentrations followed by fault message (as 

last message in sequence)

Power interruption or CPU fault

OFF or 

random

OFF or 

random

Watchdog fault

OFF

Blank or random

Instrument Fault (monitoring continues on unaffected points)

Yellow

OFF

Instrument fault

OFF

Current concentrations followed by fault message (as 

last message in sequence)

Instrument fault

(monitoring suspended)

Yellow

OFF

Instrument fault

OFF

Fault Message

Table 1-1: Instrument Alarms

珠海司福斯特科技有限公司

www.safedtech.com

Summary of Contents for CM4











































































































































































































Reviews:

No comments

Related manuals for CM4

Keithley 199 Quick Reference Manual preview
199
Brand: Keithley Pages: 49
Bamo Pooltest 3 Instruction Manual preview
Pooltest 3
Brand: Bamo Pages: 8
Vanguard Instruments II Series Operating Instructions Manual preview
II Series
Brand: Vanguard Instruments Pages: 24
Hach POCKET COLORIMETER II User Manual preview
POCKET COLORIMETER II
Brand: Hach Pages: 188
National Instruments PXIe-5665 Calibration Manual preview
PXIe-5665
Brand: National Instruments Pages: 85
National Instruments PXIe-5622 Getting Started Manual preview
PXIe-5622
Brand: National Instruments Pages: 12
National Instruments PXIe-4163 Manual preview
PXIe-4163
Brand: National Instruments Pages: 18
National Instruments USB-5683 Getting Started Manual preview
USB-5683
Brand: National Instruments Pages: 12
Watts HF scientific AccUView LED Owner'S Manual preview
HF scientific AccUView LED
Brand: Watts Pages: 40
Sig Sauer BUCKMASTERS 1500 Manual preview
BUCKMASTERS 1500
Brand: Sig Sauer Pages: 2
Hanna Instruments HI 84430 Instruction Manual preview
HI 84430
Brand: Hanna Instruments Pages: 25
FuzzDog Quack Machine Quick Start Manual preview
Quack Machine
Brand: FuzzDog Pages: 6
Lambda SRS SR475 Operation Manual preview
SRS SR475
Brand: Lambda Pages: 35
SRS Labs SXMCMTU64 Installation Instructions Manual preview
SXMCMTU64
Brand: SRS Labs Pages: 11
Hanna Instruments HI96739C Instruction Manual preview
HI96739C
Brand: Hanna Instruments Pages: 28
Kawai CN290 Owner'S Manual preview
CN290
Brand: Kawai Pages: 24
Sfere DGN 75AC User Handbook Manual preview
DGN 75AC
Brand: Sfere Pages: 22
PrimeLab 1.0 MULTITEST User Manual preview
1.0 MULTITEST
Brand: PrimeLab Pages: 353

Brands by name

Popular brands

Load more brands