manualshive.com logo in svg

Holtek HT32F50231, User Manual, Page: 97 / 486

Share
Download
Holtek HT32F50231 User Manual Download Page 97

Rev. 1.00 

97 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

6  Clock Control Unit (CKCU)

Bits

Field

Descriptions

[13]

DBI2C1

I

2

C1 Debug Mode Enable

0: Same behavior as in normal mode 

1: I

2

C1 timeout is frozen when the core is halted 

Set and reset by software.

[12]

DBI2C0

I

2

C0 Debug Mode Enable

0: Same behavior as in normal mode

1: I

2

C0 timeout is frozen when the core is halted

Set and reset by software.

[11]

DBSPI1

SPI1 Debug Mode Enable

0: Same behavior as in normal mode

1: SPI1 FIFO timeout is frozen when the core is halted

Set and reset by software.

[10]

DBSPI0

SPI0 Debug Mode Enable

0: Same behavior as in normal mode

1: SPI0 FIFO timeout is frozen when the core is halted

Set and reset by software.

[8]

DBUSR

USART Debug Mode Enable

0: Same behavior as in normal mode

1: USART timeout is frozen when the core is halted

Set and reset by software.

[6]

DBGPTM

GPTM Debug Mode Enable

0: GPTM counter continues to count even if the core is halted

1: GPTM counter is stopped when the core is halted

Set and reset by software.

[4]

DBMCTM

MCTM Debug Mode Enable

0: MCTM counter continues even if the core is halted

1: MCTM counter is stopped when the core is halted

Set and reset by software.

[3]

DBWDT

Watchdog Timer Debug Mode Enable

0: Watchdog Timer counter continues to count even if the core is halted

1: Watchdog Timer counter is stopped when the core is halted

Set and reset by software.

[1]

DBDSLP1

Debug Deep-Sleep1

0: LDO = Low power mode, FCLK = Off and HCLK = Off in Deep-Sleep1 mode

1: LDO = On, FCLK = On and HCLK = On in Deep-Sleep1 mode

Set and reset by software.

[0]

DBSLP

Debug Sleep Mode

0: LDO = On, FCLK = On and HCLK = Off in Sleep mode

1: LDO = On, FCLK = On and HCLK = On in Sleep mode

Set and reset by software.

Summary of Contents for HT32F50231







































































































































































































































































































































































































































































































Reviews:

No comments