manualshive.com logo in svg

Holtek HT32F50231, User Manual, Page: 378 / 486

Share
Download
Holtek HT32F50231 User Manual Download Page 378

Rev. 1.00 

378 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

17  Real T

ime Clock (RTC)

17  Real T

ime Clock (RTC)

RTC Control Register – RTCCR

This register specifies a range of RTC circuitry control bits.

Offset:

0x008

Reset value: 0x0000_0F00 (Reset by V

DD15

 Power Domain reset only)

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

ROLF

ROAP

ROWM

ROES

ROEN

Type/Reset

RC 0 RW 0 RW 0 RW 0 RW 0

15

14

13

12

11

10

9

8

Reserved

RPRE

Type/Reset

RW 1 RW 1 RW 1 RW 1

7

6

5

4

3

2

1

0

Reserved

LSESM

CMPCLR

LSEEN

Reserved RTCSRC

RTCEN

Type/Reset

RW 0 RW 0 RW 0

RW 0 RW 0

Bits

Field

Descriptions

[20]

ROLF

RTCOUT Level Mode Flag

0: RTCOUT Output is inactive

1: RTCOUT Output is holding as active level

Set by hardware when in the level mode (ROWM = 1) and an RTCOUT output event 

occurred. Cleared by software reading this flag. The RTCOUT signal will return to 

the inactive level after software has read this bit.

[19]

ROAP

RTCOUT Output Active Polarity

0: Active level is high

1: Active level is low

[18]

ROWM

RTCOUT Output Waveform Mode

0: Pulse mode

The output pulse duration is one RTC clock (CK_RTC) period.

1: Level mode

The RTCOUT signal will remain at an active level until the ROLF bit is cleared 
by software reading the ROLF bit.

[17]

ROES

RTCOUT Output Event Selection

0: RTC compare match is selected

1: RTC second clock (CK_SECOND) event is selected

The ROES bit can be used to select whether the RTCOUT signal is output on the 
RTCOUT pin when an RTC compare match event or the RTC second clock (CK_
SECOND) event occurs.

[16]

ROEN

RTCOUT Output Pin Enable

0: Disable RTCOUT output pin

1: Enable RTCOUT output pin

When the ROEN bit is set to 1, the RTCOUT signal will be at an active level once 
a RTC compare match or the RTC second clock (CK_SECOND) event occurs. The 
active polarity and output waveform mode can be configured by the ROAP and 
ROWM bits respectively. When the ROEN bit is cleared to 0, the RTCOUT pin will 

be in a floating state.

Summary of Contents for HT32F50231







































































































































































































































































































































































































































































































Reviews:

No comments