manualshive.com logo in svg

Holtek HT32F50231, User Manual, Page: 236 / 486

Share
Download
Holtek HT32F50231 User Manual Download Page 236

Rev. 1.00 

236 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

13  General-Purpose T

imer (GPTM)

13  General-Purpose T

imer (GPTM)

Bits

Field

Descriptions

[1]

CH1CCG

Channel 1 Capture / Compare Generation
A Channel 1 capture / compare event can be generated by setting this bit. It is cleared 
by hardware automatically.

0: No action

1: Capture / compare event is generated on channel 1

If Channel 1 is configured as an input, the counter value is captured into the 

CH1CCR register and then the CH1CCIF bit is set. If Channel 1 is configured as an 

output, the CH1CCIF bit is set.

[0]

CH0CCG

Channel 0 Capture / Compare Generation
A Channel 0 capture / compare event can be generated by setting this bit. It is 
cleared by hardware automatically.

0: No action

1: Capture / compare event is generated on channel 0

If Channel 0 is configured as an input, the counter value is captured into the 

CH0CCR register and then the CH0CCIF bit is set. If Channel 0 is configured as an 

output, the CH0CCIF bit is set.

Timer Interrupt Status Register – INTSR

This register stores the timer interrupt status.
Offset:

0x07C

Reset value: 0x0000_0000

31

30

29

28

27

26

25

24

Reserved

Type/Reset

23

22

21

20

19

18

17

16

Reserved

Type/Reset

15

14

13

12

11

10

9

8

Reserved

TEVIF

Reserved

UEVIF

Type/Reset

RW 0

RW 0

7

6

5

4

3

2

1

0

CH3OCF

CH2OCF

CH1OCF

CH0OCF CH3CCIF CH2CCIF CH1CCIF CH0CCIF

Type/Reset RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0

Bits

Field

Descriptions

[10]

TEVIF

Trigger Event Interrupt Flag

This flag is set by hardware on a trigger event and is cleared by software.

0: No trigger event occurs

1: Trigger event occurs

Summary of Contents for HT32F50231







































































































































































































































































































































































































































































































Reviews:

No comments