manualshive.com logo in svg

Holtek HT32F50231, User Manual, Page: 106 / 486

Share
Download
Holtek HT32F50231 User Manual Download Page 106

Rev. 1.00 

106 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

8  General Purpose I/O (GPIO)

8  General Purpose I/O (GPIO)

Features

 

▄

Input / output direction control

 

▄

Input weak pull-up / pull-down control

 

▄

Output push-pull / open-drain enable control

 

▄

Output set / reset control

 

▄

Output drive current selection

 

▄

External interrupt with programmable trigger edge – Using EXTI configuration registers

 

▄

Analog input / output configurations – Using AFIO configuration registers

 

▄

Alternate function input / output configurations – Using AFIO configuration registers

 

▄

Port configuration lock

Functional Descriptions

Default GPIO Pin Configuration

During or just after the reset period, the alternative functions are all inactive and the GPIO ports 

are configured into the input disable floating mode, i.e. input disabled without pull-up / pull-down 

resistors. Only the boot and Serial-Wired Debug pins which are pin-shared with the I/O pins are 

active after a device reset.

 

▄

BOOT: Input enable with internal pull-up

 

▄

SWCLK: Input enable with internal pull-up

 

▄

SWDIO: Input enable with internal pull-up

General Purpose I/O – GPIO

The GPIO pins can be configured as inputs or outputs via the data direction control registers 

PxDIRCR (where x = A ~ C). When the GPIO pins are configured as input pins, the data on the 

external pads can be read if the enable bits in the input enable function register PxINER are set. The 

GPIO pull-up / pull-down registers PxPUR / PxPDR can be configured to fit specific applications. 

When the pull-up and pull-down functions are both enabled, the pull-up function has the higher 

priority while the pull-down function will be blocked until the pull-up function is released.

The GPIO pins can be configured as output pins where the output data is latched into the data 

register PxDOUTR. The output type can be setup to be either push-pull or open-drain by the 

open drain selection register PxODR. Only one or several specific bits of the output data will be 

set or reset by configuring the port output set and reset control register PxSRR or the port output 

reset control register PxRR without affecting the unselected bits. As the port output set and reset 

functions are both enabled, the port output set function has the higher priority and the port output 

reset function will be blocked. The output driving current of the GPIO pins can be selected by 

configuring the drive current selection register PxDRVR.

Summary of Contents for HT32F50231







































































































































































































































































































































































































































































































Reviews:

No comments