Hologic Rapid fFN 10Q Page 92 User Manual Download

Page: 92 / 103

7–6

Rapid fFN 10Q

System User Manual

Section 7 — Troubleshooting

ITEM

PROBLEM

SOURCE

SOLUTION

Rapid fFN 10Q
QCette failed
during daily
quality control.

Rapid fFN 10Q
QCette or
Analyzer

Turn analyzer oﬀ and back on to reinitialize the system.

Conﬁ rm that the QCette serial number on the device
matches the serial number programmed in the analyzer,
indicated on the Daily QC printout.

Ensure QCette is clean and not damaged. The QCette may
be cleaned with canned air.

Run 3-Daily QC. If this passes, no further troubleshooting is
required.

If Daily QC fails, perform 6-3-QCette setup. If QCette setup
is complete, run 3-Daily QC, followed by 8-Liquid Controls. If
both pass, no further troubleshooting is required.

If Daily QC fails a second time, call Technical
Support.

Summary of Contents for Rapid fFN 10Q








































































































Search results

Summary of Contents for Rapid fFN 10Q

Reviews:

Related manuals for Rapid fFN 10Q

Brands by name

Popular brands

Hologic Rapid fFN 10Q, User Manual

Search results

Summary of Contents for Rapid fFN 10Q

Reviews:

Related manuals for Rapid fFN 10Q

Brands by name

Popular brands