Hologic Rapid fFN 10Q Page 80 User Manual Download

Page: 80 / 103

5–1

Rapid fFN 10Q

System User Manual

Section 5 — Care of the Anaylzer

SECTION 5 — CARE OF THE ANALYZER

GENERAL CLEANING

Keep the analyzer free of dust. If needed, clean the exterior with a damp cloth and mild detergent.

WARNING:

Liquids MUST NOT be allowed to seep into the analyzer. Keep the analyzer dry at all times.

Liquids leaking into the analyzer may cause damage to the electrical components or possibly electrical
shock to the user.

CAUTION:

DO NOT use solvents of any type on any part of the analyzer. Solvents can damage the display and keypad.

CLEANING OF CASSETTE INSERTION SITE

The cassette insertion site can come into contact with biological ﬂ uids and should be cleaned regularly.

CAUTION:

Use appropriate laboratory procedures for handling biohazardous materials.

CLEANING AGENTS APPROVED FOR USE

Reagents not listed below may cause discoloration to the analyzer case and membrane keypad.

The following cleaning agents may be applied with a cloth or lab wiper only. NEVER apply

agents by spray.

• 10% Bleach in water

• 75% Isopropyl Alcohol

• General laboratory cleaning detergent with disinfectant properties

Summary of Contents for Rapid fFN 10Q








































































































Search results

Summary of Contents for Rapid fFN 10Q

Reviews:

Related manuals for Rapid fFN 10Q

Brands by name

Popular brands

Hologic Rapid fFN 10Q, User Manual

Search results

Summary of Contents for Rapid fFN 10Q

Reviews:

Related manuals for Rapid fFN 10Q

Brands by name

Popular brands