Hologic Rapid fFN 10Q User Manual Download | Manualshive

Page: 22 / 103

background image

2–2

Rapid fFN 10Q

System User Manual

Section 2 — Installation

UNPACKING

Rapid fFN 10Q Analyzer

Carefully remove the analyzer and
accessories from the shipping carton.
Inspect the carton and the analyzer for
visible signs of damage. If the analyzer is
damaged, immediately contact the carrier
and Hologic Customer Service.
The carton should contain the following
parts/accessories:

•

Rapid fFN 10Q Analyzer

•

Wall Mount Power Adapter (with one or more AC plugs

for international compatibility)

•

User Manual

•

Rapid fFN 10Q QCette

®

Note:

Retain the shipping carton for future use. If the analyzer

needs to be shipped, use the original shipping carton.

«
...
20
21
22
23
24
...
»

Summary of Contents for Rapid fFN 10Q








































































































Reviews:

No comments

Related manuals for Rapid fFN 10Q

Brand: Hagie Pages: 61

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

MET ONE 3400 Series

Brand: Hach Pages: 48

Brand: iHealth Pages: 8

Brand: J.P. SELECTA Pages: 32

Brand: York Pages: 26

Brand: Qu-Bit Electronix Pages: 15

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

M-041 INDOOR CROSS

Brand: Salter Pages: 15

Brand: Aveo Engineering Pages: 16

Brand: Garmin Pages: 41

Brand: Eaton Pages: 38

Brand: Bison Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands