Hantek DPO6000 Series Manual Download

Page: 89 / 116

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 87 -

results and outputs a pulse.And the beeper sounds (not related to the on/off

state of the sound).

Fail ring:when a failed waveform is detected, the instrument displays the statistic

results and outputs a pulse and the beeper sounds (not related to the on/off

state of the sound).

Press

Output

softkey to show the output of test results from the

Aux

at the rear panel.

When the oscilloscope detects a waveform that does not conform to the set "mode", the

rear panel Aux will not output the waveform.If no waveform that does not conform to the

set "mode" is detected, the output pulse will continue.

Summary of Contents for DPO6000 Series





















































































































Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands

Hantek DPO6000 Series, Manual

Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands