Hantek DPO6000 Series Manual Download

Page: 75 / 116

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 73 -

1.Select waveform

Press WaveGen

→

waveform

→

index on the frontal panel.

2.Select the data source

Press WaveGen

→

data source.

3.Turn on/off the channel of signal source

Press WaveGen-

→

enable on the frontal panel.

4.Set the frequency

Press WaveGen

→

frequency on the frontal panel.

Note

: For different waveform,the frequency ranges are different. See oscilloscope

technical specifications for details.

5.Set the amplitude

Press WaveGen

→

amplitude on the frontal panel.

Press amplitude softkey to to set the amplitude of the current signal. For the setting

method, please refer to the section "

Parameter Setting Method

".When the impedance is

set to High Z, the range is from 20 mVpp to 7 Vpp; when the impedance is set to 50 Ω, the

range is from 10 mVpp to 3.5 Vpp.

6.Set the offset voltage

Press WaveGen

→

offset on the frontal panel.

Note

:When the impedance is High Z, the range is from (-3.5 V + the current amplitude/2)

to (3.5V - the current amplitude/2);when the impedance is set to 50 Ω, the range is from

(-1.75 V + the current amplitude/2) to (1.75 V - the current amplitude/2).

7.Set the phase

Press WaveGen

→

phase on the frontal panel .

The range is from 0°to 360°

8.Set the load impedance

Press WaveGen

→

impedance on the frontal panel.

Press impedance softkey to set the load input impedance of the signal generator. It can be

set to "High Z" or "50Ω".

9.Align phase

Press WaveGen

→

Align phase on the frontal panel .

The channels of the signal source will be re-configured after pressing Align phase to

output according to the preset frequency and phase. For two signals of which the

frequencies are the same or are multiples, this operation can align their phases.

The oscilloscope acquires the waveform of the two channels and displays the waveform

stably. After switching the status of the channel switch, the phase deviation between the

two waveform is changed. At this point, press

AlignPhase

softkey and the waveform

shown on the oscilloscope will restore to the phase deviation of the current phase

between the two waveform automatically.

10.Modulation

Press WaveGen

→

Modulation on the frontal panel to enter the modulation setting

interface.For detailed introduction of the modulation function, please refer to the section

Modulation

Note

:when select the waveform to be ‘‘DC’’ , ‘‘noise’’ or ‘‘Sinc’’,there is no such setting.

11.Burst

Press WaveGen

→

Burst on the frontal panel.

Summary of Contents for DPO6000 Series





















































































































Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands

Hantek DPO6000 Series, Manual

Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands