Hantek DPO6000 Series Manual Download Page 73

Page: 73 / 116

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 71 -

10.Set the load impedance

Press WaveGen

→

impedance on the frontal panel.

Press impedance softkey to set the load input impedance of the signal generator. It can be

set to "High Z" or "50Ω".

11.Align phase

Press WaveGen

→

Align phase on the frontal panel .

The channels of the signal source will be re-configured after pressing Align phase to

output according to the preset frequency and phase.

For two signals of which the frequencies are the same or are multiples, this operation can

align their phases.

The oscilloscope acquires the waveform of the two channels and displays the waveform

stably. After switching the status of the channel switch, the phase deviation between the

two waveform is changed.

At this point, press AlignPhase softkey and the waveform shown on the oscilloscope will

restore to the phase deviation of the current phase between the two waveform

automatically.

11.1.6.To output DC

1.Select waveform

Press WaveGen

→

waveform

→

DC on the frontal panel.

2.Select the data source

Press WaveGen

→

data source.

3.Turn on/off the channel of signal source

Press WaveGen-

→

enable on the frontal panel.

4.Set the offset voltage

Press WaveGen

→

offset on the frontal panel

Note

:When the impedance is High Z, the range is from (-3.5 V + the current amplitude/2)

to(3.5V - the current amplitude/2);when the impedance is set to 50 Ω, the range is from

(-1.75 V + the current amplitude/2) to (1.75 V - the current amplitude/2).

5.Set the load impedance

Press WaveGen

→

impedance on the frontal panel.

Press impedance softkey to set the load input impedance of the signal generator. It can be

set to "High Z" or "50Ω".

6.Align phase

Press WaveGen

→

Align phase on the frontal panel .

The channels of the signal source will be re-configured after pressing Align phase to

output according to the preset frequency and phase. For two signals of which the

frequencies are the same or are multiples, this operation can align their phases.

The oscilloscope acquires the waveform of the two channels and displays the waveform

stably. After switching the status of the channel switch, the phase deviation between the

two waveform is changed. At this point, press

AlignPhase

softkey and the waveform

shown on the oscilloscope will restore to the phase deviation of the current phase

between the two waveform automatically.

11.1.7.To Output Sinc

1.Select waveform

Press WaveGen

→

waveform

→

Sinc on the frontal panel.

Summary of Contents for DPO6000 Series





















































































































Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands

Hantek DPO6000 Series, Manual

Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands