Hantek DPO6000 Series Manual Download

Page: 68 / 116

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 66 -

11.Waveform generator

DPO6000C/ MPO6000D built-in 2 channels(MPO6000EDU built-in 3 channels ),25MHZ

signal source combines the signal source and oscilloscope,which greatly facilitates the

engineers who need to use both signal source and oscilloscope.The built-in signal source

can output 13 kinds of basic waveform, including sine, square, pulse, triangle,noise,DC,

sinc,exponential,half-distortion, Lorentz, dual tone and multi-frequency, Gauss, Ecg,

meanwhile provides 4 arbitrary waveform.Users can edit,load and output the arbitrary

waveform through WaveEditor software.

This chapter will introduce how to use the oscilloscope built-in signal source.Since the

functions and setting methods of two or three channels signal source are the same, this

chapter takes source 1 as an example to illustrate.

Press/click on WaveGen area on the screen to enter the control menu of the signal

source.

11.1.Output basic waveform

11.1.1.To Output Sine

1.Select waveform

Press WaveGen

→

waveform

→

sine on the frontal panel.

2.Select the data source

Press WaveGen

→

data source on the frontal panel.

3.Turn on/off the channel of signal source

Press WaveGen-

→

enable on the frontal panel.

4.Set the frequency

Press WaveGen

→

frequency on the frontal panel.

Note

:For different waveform, the frequency ranges are different. See oscilloscope

technical specifications for details.

5.Set the amplitude

Press WaveGen

→

amplitude on the frontal panel Press amplitude softkey to set the

amplitude of the current signal.When the impedance is set to High Z, the range is from 20

mVpp to 7 Vpp; when the impedance is set to 50 Ω, the range is from 10 mVpp to 3.5 Vpp.

6.Set the offset voltage

Press WaveGen

→

offset on the frontal panel.

Note

:When the impedance is High Z, the range is from (-3.5 V + the current amplitude/2)

to (3.5V - the current amplitude/2); when the impedance is set to 50 Ω, the range is from

(-1.75 V + the current amplitude/2) to (1.75 V - the current amplitude/2).

7.Set the phase

Press WaveGen

→

phase on the frontal panel.

The range is from 0° to 360°.

8.Set the load impedance

Press WaveGen

→

Load impedance on the frontal panel to set the load input impedance

of the signal generator. It can be set to "High Z" or "50Ω".

9.Align phase

Press WaveGen

→

Align phase on the frontal panel .

Summary of Contents for DPO6000 Series





















































































































Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands

Hantek DPO6000 Series, Manual

Search results

Summary of Contents for DPO6000 Series

Reviews:

Related manuals for DPO6000 Series

Brands by name

Popular brands