Hantek DPO6000 Series Manual Download | Manualshive

Page: 9 / 116

background image

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 7 -

DPO6000Z/MPO6000 Series Overview

DPO6000/MPO6000 Series is a Oscilloscope featuring extremely high memory depth,
wide dynamic range, clear display,high waveform capture rate and as many as 16 kinds of
triggering functions, 5 kinds of serial decoding functions it is a useful commissioning
instrument for various fields such as communication,aerospace, defense, embedded
systems, computers, research and education.

Main features

:

★

1 GSa/s real-time sample rate of the analog channels; 64 Mpts standard and 128M

maximum(6000EDU series) memory depth

★

1 GSa/s real-time sample rate of the digital channels

★

200 MHz, 100 MHz and 80 MHz analog channel bandwidth

★

4 analog channels, 16(4*4) digital channels(MPO6000 series;DPO6000 can update to

use digital channels by buying LP104 digital probe)

★

2-channel/3-channel signal source(MPO6000EDU is 3-channel ),13 kinds of waveform

inside,4 sets of arbitrary waveform,200M sample rate,8Kpts waveform length

★

60,000 wfms/s (dots display)/400,000 wfms/s (dots display quick acquisition mode)

waveform capture rate

★

Segmented acquisition function,support to capture up to 80,000 sections

★

256 grade color display

★

Low base noise, 500 uV/div to 10 V/div ultra-wide vertical dynamic range

★

7.0 inch WVGA (800*480) TFT LCD, with ultra-wide screen, vivid picture, low power

consumption and long service life

★

7 inch capacitive touch screen,support multi-touch(touch screen is optional)

★

Adjustable waveform brightness and display brightness

★

Up to 16 kinds of trigger functions, including 5 kinds of protocol triggers

★

Supply 5 serial decoding options

★

Auto measurement of 42 kinds of waveform parameters (with statistics)

★

5 bits digital voltage meter and 6 bits hardware frequency indicator function

★

Bode diagram function(the oscilloscopes with signal source function can use)

★

Event search function

★

2-window display function

★

Built-in FFT function

★

Multiple waveform math operation functions

【

MATH

】

★

Standard interfaces: USB Device, USB Host, LAN

★

Wifi(MPO6000EDU/DPO6000EDU can use Wifi)

★

Optional interfaces: HDMI,UART,AUX

★

Pass_fail /trig_out(EDU standard,non-EDU optional)

★

Conform to LXI CORE 2011 DEVICE class instrument standards; enable quick,

economic and efficient creation and reconfiguration of test system

★

Supports remote command control

★

Built-in help to facilitate information acquisition

★

Supports multiple languages

★

Novel and delicate industrial design and easy operation

«
...
7
8
9
10
11
...
»

Summary of Contents for DPO6000 Series





















































































































Reviews:

No comments

Related manuals for DPO6000 Series

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: Major Pages: 52

Brand: Wacker Neuson Pages: 34

Brand: MÄDLER Pages: 4

Brand: Qtx Pages: 6

home FLP 1600 SOLAR

Brand: Somogyi Elektronic Pages: 15

Brand: NEBO Pages: 2

Brand: Jumper Pages: 12

Brand: SMC Networks Pages: 2

Brand: Laserworld Pages: 34

MHL 108 WASH 150.509

Brand: Beamz Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands