Hantek DPO6000 Series Manual Download | Manualshive

Page: 5 / 116

background image

DPO6000

，

MPO6000 Series Digital Phosphor Oscilloscope Instruction V1.1

- 3 -

Summary of general safety matters

General Safety Summary

Please review the following safety precautions carefully before putting the instrument into
operation so as to avoid any personal injury or damage to the instrument and any product
connected to it. To prevent potential hazards, please follow the instructions specified in
this manual to use the instrument properly.

Avoid fire and personal injury.

Only authorized personnel can perform maintenance.

Use Proper Power Cord.

Only the exclusive power cord designed for the instrument and authorized for use within

the local country could be used.

Connect and disconnect correctly.

Connect the probe to the oscilloscope before connecting it to the circuit being

measured;Disconnect the probe and the circuit measured before disconnecting the probe

from the oscilloscope.

Ground the Instrument.

To avoid electric shock, the instrument is grounded through the Earth lead of the power

cord. The earth lead must be connected to the ground.This product must be grounded

before connecting any input or output terminals.

Connect the probe correctly.

If a probe is used, the probe ground lead must be connected to earth ground. Do not

connect the ground lead to high voltage. Improper way of connection could result in

dangerous voltages being present on the connectors, controls or other surfaces of the

oscilloscope and probes, which will cause potential hazards for operators.

Observe All Terminal Ratings.

To avoid fire or shock hazard, observe all ratings and markers on the instrument and

check your manual for more information about ratings before connecting the instrument.

Use Proper Overvoltage Protection.

Ensure that no overvoltage (such as that caused by a bolt of lightning) can reach the

product. Otherwise, the operator might be exposed to the danger of an electric shock.

Do Not Operate Without Covers.

Do not operate the instrument with covers or panels removed.

Provide Adequate Ventilation.

Inadequate ventilation may cause an increase of temperature in the instrument,which

would cause damage to the instrument. So please keep the instrument well ventilated and

inspect the air outlet and the fan regularly.

Use Proper Fuse.

Please use the specified fuses.

Avoid Circuit or Wire Exposure.

Do not touch exposed junctions and components when the unit is powered on.

«
...
3
4
5
6
7
...
»

Summary of Contents for DPO6000 Series





















































































































Reviews:

No comments

Related manuals for DPO6000 Series

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: NEC Pages: 29

Brand: Panasonic Pages: 174

Brand: Garmin Pages: 20

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

Brand: P.Lindberg Pages: 76

VLR100 LED Series

Brand: WE-EF Pages: 3

Brand: ProLights Pages: 28

Brand: Wang Pages: 146

Brand: Measumax Pages: 2

Brand: Woods Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands