Recipe Setup
9–18
Flow Meter Calibration Procedure
Selection 1, 2, 3, or 4: Calibrating the
Meters Individually
NOTE:
Take a large sample (1000 cc or more) of a
fluid that is a known accurate weight per gallon so that
any error in measuring the sample is spread out.
WARNING
PRESSURIZED EQUIPMENT HAZARD
To avoid splashing fluid in the eyes when
calibrating the meters:
Wear eye protection.
Only open the ratio check valves enough to
allow fluid to flow at a rate of 100 to 200 cc per
minute.
CAUTION
The fluid shut-off valves and ratio check valves are
retained in their housings by mechanical stops that
prevent accidental removal of the valve stem while
the manifold is pressurized. Do not use a tool to
open or close the valve stems. If manual force
cannot turn the valve stems, the system pressure
must be relieved and the valve properly disas-
sembled and cleaned to remove the resistance.
1.
Make sure the operator switch is set at
Standby
.
CAUTION
Both the Component A, B, and C fluid shut-off valves
must be closed if you choose to do a calibration test.
Selecting enter on the calibration menus will auto-
matically open the dispense valve for the meter
being tested.
2.
Enter selection 1, 2, 3, or 4 for the flow meter you
want to calibrate.
SETUP
Recipe: 1
Station: 1
METER CALIBRATION TESTS
1. COMPONENT A FLOW METER CALIBRATION
2. COMPONENT B FLOW METER CALIBRATION
3. COMPONENT C FLOW METER CALIBRATION
4. SOLVENT FLOW METER CALIBRATION
5. MIXED MATERIAL CALIBRATION
Select a menu item and press enter:
> 1
3.
Close the Component A, B, and C fluid shut-off
valves and ratio check valves.
4.
Place a waste container under the ratio check
valve tube for the meter being tested.
5.
Press Enter
to begin calibration.
SETUP
Recipe: 1
Station: 1
COMPONENT A FLOW METER CALIBRATION
Enter Component A Meter K-Factor:
> 0.124 cc/pulse
Press Enter to begin calibration:
> STOP
Calibration Volume is 0 cc
Enter new Calibration Volume:
> 0 cc
-OPERATOR SWITCH MUST BE IN STANDBY-
6.
Open the Component A ratio check valve and
dispense about 50 cc to clear the tube of any air.
Close the ratio check valve.
7.
Press the Previous
key to stop the calibra-
tion. Enter selection 1 to calibrate component A
again.
Continued on the next page.
Summary of Contents for PrecisionMix ii
