Recipe Setup
9–9
Recipe Setup
Screens
Information
S3
System Alarms with
Flow Control On
and
Hand Gun
Selected
SETUP
Recipe: 1
Station: 1
SYSTEM ALARMS
Enter Gun 1 Potlife Time Limit:
> 000 minutes
Enter Gun 1 Potlife Timer Reset:
> 0000 cc
Enter Gun 2 Potlife Time Limit:
> 000 minutes
Enter Gun 2 Potlife Timer Reset:
> 0000 cc
Enter Flow Rate Alarm Tolerance
> 0000 %
Enter Low Limit Below Flow Rate Setpoint
> 0000 cc/min
Type the desired number entry for each field.
Press
after each entry.
Next screen
.
Fig. 9.1
NOTE:
This is not an User Interface screen.
Delay Time
Time
Flow
Low Limit
Alarm
Tolerance
Flow Rate Setpoint
Gun “feathered”,
No Flow Control
Full Flow Control
Alarm
Tolerance
Gun Potlife Time Limit
Sets the maximum time allowed for mixed fluid to be in
the system before tripping a pot life alarm. The timer
starts when catalyst is introduced into the integrator.
Follow the material recommendation when setting a
value.
The pot life timer is reset either by a purge or
by the passage of a specified amount of fluid.
The guns that appear for potlife time limit and
timer reset depends on the guns selected
during system configuration. Refer to page
8–10.
Gun Potlife Timer Reset
Sets the volume of fluid that needs to be dispensed
before the pot life timer resets. Enter a value that
represents the volume of mixed fluid that is in the
integrator, hoses, and guns.
Flow Rate Alarm Tolerance
(Refer to Fig. 9.1)
Sets the alarm tolerance percentage in relation to the
flow rate setpoint. The tolerance percentage should be
outside of the low limit setpoint. The flow rate alarm
output will be on when the actual flow rate falls out of
this tolerance for three seconds. The alarm output will
be off when the actual flow rate falls within this toler-
ance.
For the gun 1 flow rate alarm, output #2 of module
#2 will be on.
For the gun 2 flow rate alarm, output #3 of module
#2 will be on.
Low Limit Below Flow Rate Setpoint
This setting helps the system allow for periodic partial
triggering of a hand gun without adjusting the flow rate.
See page 9–9 for a detailed information on Flow
Control Low Limit.
Summary of Contents for PrecisionMix ii
