manualshive.com logo in svg

GE LOGIQ 400, Service Manual

Share
Download
GE LOGIQ 400 Service Manual Download Page 92

GE MEDICAL SYSTEMS

2127661

LOGIQ   400 SERVICE MANUAL

FUNCTIONAL CHECKS

4–28

REV 5

4–3–3 Utility Menu (Continued)

(G) SOFTWARE CONFIGURATION DISPLAY

This displays the configurations of all system software installed in the console.

Type 7 and then press Return key when the Utility Menu is displayed. The Software Configuration Display is
displayed as shown in ILLUSTRATION 4–21.

SOFTWARE CONFIGURATION DISPLAY

ILLUSTRATION 4–21

Note

The configuration indicated on the software configuration display is different depending on the soft-
ware version of console.

Summary of Contents for LOGIQ 400















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands