manualshive.com logo in svg

GE LOGIQ 400, Service Manual

Share
Download
GE LOGIQ 400 Service Manual Download Page 226

GE MEDICAL SYSTEMS

LOGIQ   400 SERVICE MANUAL

2127661

RENEWAL PARTS

6–96

REV 9

6–2–15 Fixing Metal Plate (FRU No. 154)

Time Required

5 Minute

Tool Required

Screwdriver

Procedure

Refer to ILLUSTRATION 6–34.

1.

Turn OFF the system.

2.

Remove the Monitor Bottom Assy (FRU 157). Refer to 6–2–17 on page 6–98.

3.

Pull out the Fixing Metal Plate (FRU 154) from the Escutcheon Assy (FRU 153).

FIXING METAL PLATE REMOVAL

ILLUSTRATION 6–34

Summary of Contents for LOGIQ 400















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands